Used  Welding Machinery Monthly Sales Products Special Sales Contact Us Site Map


Inventory Welding Machinery List

welding positioning equipment

 

Used Welding Machinery and Equipment


P810022 Aronson B-200 Bench Mount Manual Positioner
200 lb. capacity at 12” center of gravity
360° manual rotation with friction breaking
360 ° manual tilt with friction breaking 360 ° manual revolving base 6” diameter round table 12.5” table height Shipping weight 100 lbs. Serial #93873

P120701 Ransome B 2.5 Bench Mount Positioner 250 lb. capacity at 3” center of gravity 360° variable speed rotation 135° manual tilt 20” diameter solid round table 16.5” table height 115 volt Shipping weight 400 lbs. Serial #116931

P411003A Pandjiris 2.5 MVRHT 250 lb. Positioner 250 lb. capacity at 4” center of gravity 360° variable speed rotation 90° manual tilt 18” diameter round table 35.5” height with 16” riser 115V. Shipping weight 1,200 lbs. Serial #25-1289-2

P810013 Aronson AW-300A 300 lb. Positioner 300 lb. capacity at 12” center of gravity .2 to 6.0 RPM variable speed rotation 360° manual tilt with brake and 45° pin lock indexing 8” diameter round table Forward/stop/reverse foot pedal Pendant control 120 volt Shipping weight 260 lbs. Serial #510-90179

P810014 Aronson AW-300A 300 lb. Positioner 300 lb. capacity at 12” center of gravity .2 to 6.0 RPM variable speed rotation 360° manual tilt with brake and 45° pin lock indexing 8” diameter round table Forward/stop/reverse foot pedal Pendant control 120 volt Shipping weight 100 lbs. Serial #N/A

P810031 Aronson AW-300A 300 lb. Positioner 300 lb. capacity at 12” center of gravity .2 to 6.0 RPM variable speed rotation 360° manual tilt with brake and 45° pin lock indexing 8” diameter round table Forward/stop/reverse foot pedal Pendant control 120 volt Shipping weight 100 lbs. Serial #N/A

P994007 Standard Machine Co. 400 lb. Positioner Approximately 400 lb. capacity power hydraulic tilt Variable speed rotation 13” diameter table w/slots Fixed height of 26” center line of rotation  

P140501 Cinti 500 lb. High Speed Positioner. Designed for Plasma Thermal Spray 500 lb. capacity at 12” center of gravity manual tilt Variable high speed rotation at 2-240 RPM Fixed table height at 39 1/2” 24” round table with slots Pendant control for all functions 115 volt Shipping weight 1,100 lbs. Serial #N/A  

P140502 Cinti 500 lb. High Speed Positioner. Designed for Plasma Thermal Spray  500 lb. capacity at 12” center of gravity Manual tilt Variable high speed rotation at 2-240 RPM Fixed table height at 40 1/2” 24” round table with slots Pendant control for all functions 115 volt 1 phase Shipping weight 1,100 lbs. Serial #N/A  

P140503 Cinti 500 lb. High Speed Positioner. Designed for Plasma Thermal Spray  500 lb. capacity at 12” center of gravity Manual tilt Variable high speed rotation at 2-240 RPM Fixed table height at 40 1/2” 30” round table with slots Pendant control for all functions 230 volt 1 phase Shipping weight 1,500 lbs. Serial #N/A  

P9911008 Aronson BT-500A 500 lb. Welding Positioner  500 lb. capacity variable speed Manual side arm tilt 8” diameter 3-jaw chuck Needs vertical mounting pipe Foot controls Shipping weight 200 lbs. Serial #77785 

P810015 Aronson BT-500 500 lb. Positioner  500 lb. capacity at 12” center of gravity .33 to 10.0 variable speed rotation by a Grahm drive 360° manual rotation with brake 6” diameter round table Forward/stop/reverse foot pedal 120 volt Shipping weight 200 lbs. Serial #5348

P404008 Ransome 5P 500 lb. Positioner  ***PARTS ONLY*** 500 lb. capacity at 6" center of gravity 135° constant speed powered tilt 360° mechanical variable speed rotation from .06 to 2.0 RPM 30" diameter table with slots Adjustable table height from 32” to 47” in 5” increments Pendant control 480 volt Shipping weight 1,200 lbs. Serial # 1314851

P130501 Ransome 5R 500 lb. Positioner  500 lb. capacity at 6" center of gravity 135° constant speed powered tilt 360° mechanical variable speed rotation from .06 to 2.0 RPM 26" diameter table with slots Adjustable table height from 28 1/2” to 43 1/2” in 5” increments Pendant control 480 Volt Shipping weight 1,200 lbs. Serial # 55946

P110803 Pandjiris 7.5-4FB 750 lb. Positioner  750 lb. capacity at 4" center of gravity 135° manual tilt Variable speed rotation from .08 to 1.60 RPM Table height 30” 18" round table with slots 25' pendant control Variable speed foot pedal 115 volt Shipping weight 400 lbs. Serial # 81-2393

P111105 Pandjiris Model 10-4 1,000 lb. Positioner  without chuck 1,000 lb. capacity at 4" center of gravity power tilt with chuck Variable speed rotation from .040 to 2.0 RPM Manual adjustable table height from 33 1/2" to 43 1/2" in 5" increments with 7” riser 24" round solid table Includes 16” self-centering scroll chuck Pendant control On/off foot pedal 480/115 volt Shipping weight 1,500 lbs. Serial #W599-4

P120403 Teledyne Readco Model UPC-10 1,000 lb. Positioner  1,000 lb. capacity at 6" center of gravity power tilt Variable speed rotation from .040 to 2.0 RPM Manual adjustable table height from 31 1/4" to 55 1/4" in 6" increments 29" round table with slots Pendant control On/off foot pedal 460 volt Shipping weight 1,050 lbs. Serial #104196  

P305001 Ransome SW-10A 1,000 lb. Twin Axis Positioner  1,000 lb. capacity at 6" center of gravity 360° constant speed powered side arm tilt Variable speed rotation from .06 to 2.0 RPM 36" diameter table with slots On/off foot pedal 115 volt Serial #9321389  

P150424 Aronson Model HS10BBH/T30-3 Skyhook Positioner 2,500 lb. load capacity Center of gravity 28" Overhang 3' Off-center 22" table with a 9" diameter thru hole "Skyhook" positioners provide part rotation in two 360° axis which result in partial or full inverting of the work piece 10' pendant control 460 volt Serial #n/a Shipping dimensions: 7' long x 5' wide x 5' high Shipping weight: 4,750 lbs. Reconditioned:

P150601 Ransome Model 25P 2,500 lb. Positioner  2,500 lb. capacity at 6” center of gravity 135° power tilt Variable speed rotation from .03 to 1.55 RPM Manual adjustable elevation from 35.25” to 53.25” in 6" increments 32" round table with slots and a 2" diameter through hole 25' pendant control for all functions 115 volt Shipping weight 2,500 lbs. Shipping dimensions: 6' long x 4' wide x 5" high Serial #1616294

P150407 Aronson Model HD-25CS 2,500 lb. Positioner  2,500 lb. capacity at 6” center of gravity 135° power tilt Variable speed rotation from .07 to 2.0 RPM Manual adjustable elevation from 34.5” to 56.5” in 5.5" increments 42" round table with slots Pendant control for all functions 460 volt Shipping weight 1,500 lbs. Shipping dimensions: 5' long x 4.5' wide x 48" high Serial #801501

P150408 Aronson Model HD-25 2,500 lb. Positioner  2,500 lb. capacity at 6” center of gravity 135° power tilt Variable speed rotation from .07 to 2.0 RPM Manual adjustable elevation from 36” to 58” in 5.5" increments 30" x 30" square table with slots Pendant control for all functions 460 volt Shipping weight 1,500 lbs. Shipping dimensions: 5' long x 4.5' wide x 36" high Serial #741188

P140708 Aronson HD-25 2,500 lb. Positioner w/foot pedal 2,500 lb. capacity at 6” center of gravity with chuck 135 ° power tilt Variable speed 30” square table Manual table adjustable from 36 ½” to 58 ½” in 5 ½” increments 15’ pendant control 20’ forward/stop/reverse foot control 18 inch self-centering chuck with adapter plate – 3 grippers and 3 T-slots 230 volt - 3 phase Shipping dimensions 6’L x 4’W x 4’ H Shipping weight 2,000 lbs. Serial #67908  

P803018 Aronson Model HD-25 2,500 lb. Positioner ***PARTS ONLY*** 2,500 lb. capacity at 6” center of gravity Power tilt Variable speed rotation from .07 to 2.0 RPM Manual adjustable table height from 34.5” to 56.5” in 5” increments 30” square table with slots Pendant control for all functions Forward/stop/reverse foot pedal 230 or 460 volt Shipping weight 1,500 lbs. Serial #N/A

P111206 Worthington/Ransome Model 25P 2,500 lb. Positioner Constant Speed 2,500 lb. capacity at 6” center of gravity  Variable speed 135° power tilt Variable speed rotation from .038 to 1.55 RPM Adjustable table height from 41” to 59” in 6” increments 32” x 32” square slotted table Pendant control 460 volt Shipping weight 2,100 lbs. Serial #56669  

P101201 Ransome Model 25P 2,500 lb. Positioner  2,500 lb. capacity at 6” center of gravity 135° power tilt Variable speed rotation from .038 to 1.55 RPM 43” fixed table height 60” diameter round table Pendant control 230 or 460 volt Shipping weight 2,100 lbs. Serial #49398

P130603 Ransome Model 25P 2,500 lb. Positioner 2,500 lb. capacity at 6” center of gravity 135° power tilt Variable speed rotation from .038 to 1.55 RPM Adjustable table height from 44” to 62” in 6” increments 32”x 32” square slotted table Pendant control 230 volt Shipping weight 2,100 lbs. Serial #7664

P406002 Webb 25P, 2,500 lb. Positioner  2,500 lb. capacity at 6" center of gravity Power tilt .15 to 1.5 variable speed rotation 36" fixed table height 30" diameter round table with slots Pendant control Serial #N/A

P120306 Reed/Webb Model P25R 2,500 lb. Positioner  2,500 lb. capacity at 6” center of gravity Power tilt Variable speed rotation from .07 to 2.0 RPM Fixed table height at 34.5” 30” round table with slots Pendant control for all functions 230 or 460 volt Shipping weight 1,500 lbs. Serial # 511788

P709005 P & H Model WP-2 2,500 lb. Positioner  2,500 lb. capacity at 6” center of gravity Manual/hydraulic tilt Variable speed rotation Manual adjustable height from 24” to 40” in 6” increments Pendant control 230/460 volt Serial #WP-2447

P110508 Sciaky WP-1AB 2,500lb Positioner  2,500 lb. capacity at 12” center of gravity 135° power tilt Variable speed euro drive rotation Manual adjustable height from 35” to 51” 40” round solid table with T-slots and 9“through hole 230 volt - 3 Phase Serial #7481

P130502 Sciaky WP-1AB 2,500 lb. Positioner  2,500 lb. capacity at 12” center of gravity 135° power tilt Variable speed rotation - no back lash Manual adjustable height from 35” to 51” 40” round 1 1/2" thick solid table with T-slots and 9“through hole 230 volt - 3 phase Serial #N/A

P510009 Koike-Aronson HS10BBH/T3-30 "Skyhook" Positioner  2,500 lb. load capacity Center of gravity 28" Overhang 3" Off-center 38" table "Skyhook" positioners provide part rotation in two 360° axis which result in partial or full inverting of the work piece Pendant control Serial #80308

P510010 Koike-Aronson HS10BBH/T3-30 "Skyhook" Positioner 2,500 lb. load capacity Center of gravity 28" Overhang 3" Off-center 38" table "Skyhook" positioners provide part rotation in two 360° axis which result in partial or full inverting of the work piece Pendant control Serial #N/A

P150409 Aronson Model RAB-30 3,000 lb. Positioner  3,000 lb. capacity at 6” center of gravity 135° power tilt Variable speed rotation from .07 to 2.0 RPM Manual adjustable elevation from 38.5” to 64.5” in 6" increments 36" round table with slots Pendant control for all functions 460 volt Shipping weight 3,200 lbs. Shipping dimensions: 7' long x 5' wide x 39" high Serial #8112 Reconditioned -

P140603 Pandjiris 30-6AB Pandjiris 3,000 lb. Positioner  3,000 lb. capacity at 6" center of gravity 135° constant speed power tilt Variable speed rotation from .07 to 1.40 RPM Manual adjustable height from 32 1/2" to 52 1/2" in 5" increments 30" x 30” square table with slots Pendant control for all controls 230 Volt – 3 phase Serial #400-7834 Shipping weight 1,750 lbs.

P304011 Ardmore Electro-Hydraulic Tilting Positioner  4,000 lb. capacity at 12” from the table 360° hydraulic rotation Hydraulic lift and tilt 16” diameter work table Serial #N/A Shipping weight 4,750 lbs. Hydraulic/460 volt  

P120304 Arborfer Model PAF0010PHS Hydraulic 4,000 lb. Positioner  4,000 lb. capacity at 12” center of gravity  converted to 480 volt 90° constant speed power tilt Variable speed rotation adjusted by hydraulic pressure 60” round slotted table Fixed table height at 49” 575 volt Shipping weight 4,100 lbs. Serial # 1001011089 

P611020 Aronson Model HS30GE/T4-62 Sky Hook Positioner  4,000 lb. capacity at 36” center of gravity off of the turntable face 62” clearance from center of turntable "Skyhook" positioners provide part rotation in two 360° axis which result in partial or full inverting of the work piece Pendant control Serial #7914

P150410 Preston-Eastin Model PA-45-12, 4,500 lb. Positioner  4,500 lb. capacity at 12” center of gravity 135° power tilt Variable speed rotation from .04 to 1.18 RPM Manual adjustable elevation from 37” to 62” IN 5" increments 42" x 42" Square table with slots Pendant control for all functions 460 volt Shipping weight 3,500 lbs. Shipping dimensions: 75" long x 48" wide x 37" high Serial #5118

P810026 Aronson GE-45 Geared Elevation Positioner  4,500 lb. capacity at 12” center of gravity 135° power tilt .01 to 1.2 variable speed rotation Powered elevation from 53” to 86” 42” square table with slots Pendant control Shipping weight 5,700 lbs. Serial #N/A

P131001P Aronson GE-45B Geared Elevation Positioner  4,500 lb. capacity at 12” center of gravity 135° power tilt. .02 to 1.2 variable speed rotation Powered elevation from 54” to 87” 48” round table with slots 9” thru hole Pendant control Shipping weight 5,700 lbs. Serial # 6920  

P140903P Ransome Model 14 6,000 lb. Positioner  6,000 lb. at 12” center of gravity 135° power tilt Constant speed rotation 45” x 45” square table with slots Fixed table height of 52 inches 20’ pendant control 230 volt – 3 phase Serial number #5120 Shipping dimensions: 8’L x 68”W x 52”H Shipping weight: 7,500 lbs.

P140904P Ransome Model 14 6,000 lb. Positioner 6,000 lb. at 12” center of gravity 135° power tilt Constant speed rotation 45” x 45” square table with slots Fixed table height of 52 inches 20’ pendant control 460 volt – 3 phase Serial number #5484 Shipping dimensions: 8’L x 68”W x 52”H Shipping weight: 7,500 lbs.

P111205 Worthington/Ransome Model 60P 6,000 lb. Positioner  ***PARTS ONLY*** 6,000 lb. capacity at 12” center of gravity 135° power tilt Variable speed rotation from .038 to 1.55 RPM 51” fixed table height 46”x 46” square slotted table Pendant control 480 volt Serial #53378

P130504 Cullen-Freistedt Model 60 6,000 lb. Positioner  6,000 lb. capacity at 12” center of gravity 135° power tilt Constant speed rotation Manual adjustable table height from 62” to 74” with the table flat 40” x 40” square 7/8” thick table Pendant control 460 volt Serial #732

P131002P Aronson GE-60A Geared Elevation Positioner  6,000 lb. capacity at 12” center of gravity 135° power tilt .05 to 1.5 variable speed rotation Powered elevation from 60” to 93” 48” round table with slots Pendant control Shipping weight 7,300 lbs. Serial #7935 

P810001 Aronson 180T120/CC 180 ° Tilter  7,000 lb. weight capacity at 12” center of gravity from table Table tilts 180° from vertical to vertical For positioning long work pieces such as long truck frames for down hand welding Table does NOT rotate Table is a dual screw clamping table with an internal capacity of 40” wide x 27.5” high Serial #N/A

P805005 Teledyne-Readco Model UHSE-400 7,500 lb. Side Arm Positioner Side arm positioners are also known as Skyhook positioners 7,500 lb. capacity at 6” center of gravity Dual screw driven powered elevation from 31.5” to 77.5” w/side arm table flat and parallel to the floor 51” to the center of the rotational axis with the side arm at 90° to the floor Side arm table is 3.5” off set to the center of the rotational axis on the headstock Variable speed rotation of the side arm table 88” maximum part diameter capacity Pendant control for all functions 460 volt Serial #106130

P805006 Teledyne-Readco Model UHSE-400 7,500 lb. Side Arm Positioner Side arm positioners are also known as Skyhook positioners 7,500 lb. capacity at 6” center of gravity Dual screw driven powered elevation from 31.5” to 77.5” w/side arm table flat and parallel to the floor 51” to the center of the rotational axis with the side arm at 90° to the floor Side arm table is 3.5” off set to the center of the rotational axis on the headstock Variable speed rotation of the side arm table 88” maximum part diameter capacity Pendant control for all functions 460 volt Serial #106133

P150505 Unique Model UPC-100 10,000 lb Positioner  10,000 lb. capacity at 12” center of gravity 135° power tilt Variable speed rotation Manual adjustable elevation from 48” to 84” in 6" increments 48" square table with slots 20' pendant control for all functions 20' forward/stop/reverse foot pedal 460 volt Shipping weight 6,500 lbs. Shipping dimensions: 88" long x 66" wide x 72" high Serial #n/a

P110906 Pandjiris Model DC-150-VPL “Drop-Center” Positioner Rotation capacity of 12,000 lbs. at 12” center of gravity off of the centerline of rotation Constant speed powered elevation Center section has two adjustments from 25” to 97” and 45” to 117” Inside distance between upright sides is 20’ 360° rotation at 0.0-2.0 RPM 200° tilt at 0.0-1.75 RPM Table is 60” Round with slots Serial #N/A Note; “Drop Center positioners” are typically used for work pieces with longer center of gravity distances from the table, resulting in lower working or welding heights than using higher capacity positioners.

P110907 Pandjiris Model DC-150-VPL “Drop-Center” Positioner Rotation capacity of 12,000 lbs. at 12” center of gravity off of the centerline of rotation Constant speed powered elevation Center section has two adjustments from 25” to 97” and 45” to 117” Inside distance between upright sides is 19’ 360° rotation at 0.0-2.0 RPM 200° tilt at 0.0-1.75 RPM Table is 60” Round with slots Serial #60-4567 Note; “Drop Center positioners” are typically used for work pieces with longer center of gravity distances from the table, resulting in lower working or welding heights than using higher capacity positioners.

P110908 Pandjiris Model DC-150-VPL “Drop-Center” Positioner Rotation capacity of 12,000 lbs. at 12” Center of gravity off of the centerline of rotation Constant speed powered elevation Center section has two adjustments from 28” to 118” Inside distance between upright sides is 19’ 360° rotation at 0.0-2.0 RPM 200° tilt at 0.0-1.75 RPM Table is 42” Round with slots Serial #60-4566-1 Note; “Drop Center positioners” are typically used for work pieces with longer center of gravity distances from the table, resulting in lower working or welding heights than using higher capacity positioners.

P140905P Cullen Friestadt Model 140 14,000 lb. Positioner 14,000 lb. at 12” center of gravity or 12,000 lb. at 18” center of gravity 135° power tilt Constant speed rotation 54” x 54” square table, no slots Manual adjustable table height from 70” to 87 1/4" 20’ pendant control 230 volt – 3 phase Serial number #3873 Shipping dimensions: 90”L x 66”W x 61”H Shipping weight: 7,800 lbs.

P140706 Ransome 16,000 lb. Positioner 16,000 lb. at 12” Center of Gravity 135° power tilt Variable speed rotation 53” square table with slots Fixed table height at 60 ½” Two 10’ pendant controls 460 volt 3 phase Serial #6986 Shipping dimensions: 9’ L x 6’ W x 60 ½” H Shipping weight 7,500 lbs.

P140305 Gabco 16,000 lb. Hydraulic Beam Positioner 16,000 lb. capacity at 48” off faceplate 100” maximum diameter with table vertical Constant speed at .5 RPM 25 degree tilt up and 20 degree tilt down Hydraulic lever and push button controls 12” x 80” load beam with multiple adjustment holes for fixturing 460 volt – 3 phase hydraulic Serial #561 Shipping weight 10,000 lbs.

P140306 Gabco 16,000 lb. Hydraulic Beam Positoner 16,000 lb. capacity at 48” off faceplate 100” maximum diameter with table vertical Constant speed at .5 RPM 25° tilt up and 20° tilt down Hydraulic lever and push button controls 12” x 80” load beam with multiple adjustment holes for fixturing 460 volt – 3 phase Hydraulic Serial #N/A Shipping weight 10,000 lbs.

P140504 P&H Model WP-12 16,800 lb. Positioner Working 16,800 lb. capacity at 12” center of gravity  Reconditioned 135° power tilt Mechanical variable speed rotation from .006 to .6 RPM Powered elevation from 78” to 119” with table horizontal 7' x 7' slotted square table Pendant controls for tilt and elevation Pendant and foot pedal for rotation control 460 volt – 3 phase Shipping weight 14,000 lbs. Serial #1150

P131114P Aronson Model AB-180CS 18,000 lb. Positioner 18,000 lb. capacity at 12” center of gravity 135° power tilt Variable speed rotation from .006 to .6 RPM Manual adjustable elevation from 54” to 90” 48” x 1 3/4” solid round table with 9” thru hole Pendant control for all functions 460 volt Shipping weight 7,650 lbs. Serial #95102

P111004 Ransome Model 200P 20,000 lb. Positioner 20,000 lb. capacity at 12” center of gravity 90° power tilt Variable speed rotation from .025 to 1.0 RPM 54” x 54” square table with slots Fixed table height of 51” Pendant control for all functions Serial #N/A

P131008P Cullen-Freistedt Model 200 20,000 lb. Positioner 20,000 lb. capacity at 20” center of gravity 135° power tilt Variable speed rotation from .025 to 1.0 RPM 48” round table Fixed table height of 52” Pendant control for all functions Serial #153

P150206 Aronson Model HD-240B 24,000 lb. Positioner  24,000 lb. capacity at 12” center of gravity 135° power tilt Variable speed rotation from .006 to .6 RPM Manual adjustable elevation from 59” to 95” IN 6" increments 54" x 54" Square table with slots Pendant control for all functions 460 volt Shipping weight 7,800 lbs. Shipping dimensions: 8' long x 7' wide x 60" high Serial #67764

P140907P Worthington Model 240P Positioner 24,000 lb. capacity at 12” center of gravity 135° tilt Variable speed rotation from .01 to .6 RPM 60”x60” square table with slots 20’ pendant control 230 volt – 3 phase Shipping Dimensions 10’L x 92”W x 69”H Shipping weight 8,500 lbs.

P131009P Aronson Model HD-240A 24,000 lb. Positioner As-Is 24,000 lb. capacity at 12” center of gravity 135° power tilt Variable speed rotation from .006 to .6 RPM Manual adjustable elevation from 59” to 95” 54” x 54” square table with slots Pendant control for all functions and foot pedal for rotation control 460 volt Shipping weight 7,650 lbs. Serial #79200

P140906P Aronson Model HD-240 24,000 lb. Positioner 32,000 lb. at 6” center of gravity or 24,000 lb. at 12” center of gravity 135° power tilt Variable speed rotation 54” x 54” square table with slots Manual adjustable table height from 61” to 97” in 6” increments 20’ pendant control 230 volt – 3 phase Serial number #6647 Shipping dimensions: 9’L x 90”W x 70”H Shipping weight: 7,500 lbs. 

P150506 Ransome Model 250P, 25,000 lb. Positioner  25,000 lb. capacity at 12” center of gravity 135° power tilt Variable speed rotation from .012 to .49 RPM Manual adjustable table height from 59” to 83” IN 6" increments 60" round table with slots and a 7.5" through hole 20' Pendant control for all functions 20'foward/stop/reverse foot pedal 460 volt Shipping weight 12,000 lbs. Shipping dimensions: 8' long x 7' wide x 5' high Serial #2831985 Reconditioned

P150507 Aronson model G-600, 40,000 lb. Positioner 40,000 lb. capacity at 12" center of gravity 90° power tilt Variable speed rotation from .007 to .4 rpm 12' diameter round table 35' pendant control 460 volt Serial #647 Shipping dimensions: 12' long x 12' wide x 89" high Shipping weight: 23,000 lbs.

P110911 Ransome Model 400P 40,000 lb. Positioner As-Is 40,000 lb. capacity at 12” center of gravity 135° power tilt Variable speed rotation from .025 to 1.0 RPM Variable speed tilt 72” diameter round table with slots Adjustable table height of 106” to 118” in 6” increments Currently mounted atop 13 1/2” I-beam risers Pendant control for all functions Also includes fixturing for mounting round tank heads 460 volt 3phase Shipping weight 35,000 lbs. Serial #24-2400

P121021P Worthington Model 400 40,000 lb. Positioner 40,000 lb. capacity at 12” center of gravity 135° power tilt Variable speed rotation from .2 to 3.0 RPM Powered elevation with 48 inches of travel 7’ x 7’ square table with slots Pendant control for all functions 230 volt 3 phase Shipping weight 35,000 lbs. Serial #2867379  

P131111P Aronson Model G-400A 40,000 lb. Positioner 40,000 lb. capacity at 12” center of gravity Variable speed rotation from .016 to .50 RPM Rotation torque 480,000 lb./inch 90° of tilt forward and 45° of tilt backward 7’ x 7' square table with T-slots and 12” thru hole spindle Fixed table height at 91” from the floor with 10” riser Remote pendant control for all functions 480 volt 3 Phase Serial # 7517 Shipping weight 16,300 lbs.

P130403 Aronson Model HD-500 50,000 lb. Positioner 50,000 lb. capacity at 12” center of gravity 135° power tilt Four speed rotation with manual transmission Fixed height at 72” 96” x 96” square table with slots and 12” thru hole Pendant control for all functions 460 volt Shipping weight 22,500 lbs. Serial# 647 Rental Available on this Unit!!

P131112P Aronson Model G-500 50,000 lb. Positioner 50,000 lb. capacity at 12” center of gravity Variable speed rotation from .5 to .008 RPM Rotation torque 600,000 lb./inch 90° of tilt forward and 45° of tilt backward 7’ x 7' square table with T-slots and 12” thru hole spindle Fixed table height at 94 1/2” from the floor with 13 1/2” riser Remote pendant control for all functions 480 volt 3Phase Serial #663 Shipping weight 16,500 lbs.

P121216 Aronson Model HD-600 60,000 lb. Positioner  60,000 lb. capacity at 12” center of gravity 135° power tilt Variable speed rotation from .006 to .6 RPM Fixed elevation at 142” 8’ round table with slots and 12” thru hole Pendant control for all functions 460 volt Shipping weight 46,000 lbs. Serial# 693

P130402 Aronson Model HD-600 60,000 lb. Positioner 60,000 lb. capacity at 12” center of gravity 135° power tilt Variable speed rotation from .006 to .6 RPM Adjustable height from 74” to 122” in 12” increments 96” x 96” square table with slots and 12” thru hole Pendant control for all functions 460 volt Shipping weight 18,800 lbs. Serial #7813

P130520P Aronson Model AB-850A 85,000 lb. Positioner 85,000 lb. capacity at 12” center of gravity Variable speed rotation from .004 to .40 RPM Rotation torque 1,020,000 lb./inch tilt, torque 1,800,000 lb./inch over 135° of tilt movement 13’ diameter round table with 8 T-slots Manual table height adjustment from 73” to 127” from floor Remote pendant control for all functions Machine was rebuilt in 1999 480 volt 3 Phase Serial #847 Shipping weight 39,500 lbs.

P130404 Brantford Tool Model LP 60T 120,000 lb. Hydraulic Positioner 120,000 lb. capacity at 12” center of gravity 90° hydraulic powered tilt Variable speed rotation from .006 to .6 RPM 113” round table with (6) T-slots 74” table height horizontal 123” to the center of table vertical 8’ 6” maximum diameter in vertical position Pendant control for all functions 575 volt Shipping weight 48,500 lbs. Serial #3671


UNI-BALANCE POSITIONERS

P810005 Aronson C-4000 Universal Balance Positioner 4,000 lb. capacity at 12” from the table 360° manual rotation 12” to 84” manual table height range 12” diameter work table These are manual balanced machines – they are typically used for weldments that require quick re-positioning such as boxes, frames, etc. Serial #83299 Shipping weight 1300 lbs.

P810007 Aronson C-4000 Universal Balance Positioner 4,000 lb. capacity at 12” from the table 360° manual rotation 12” to 84” manual table height range 12” diameter work table These are manual balanced machines – they are typically used for weldments that require quick re-positioning such as boxes, frames, etc. Shipping weight 1300 lbs. Serial #N/A

P810008 Aronson C-4000 Universal Balance Positioner 4,000 lb. capacity at 12” from the table 360° manual rotation 12” to 84” manual table height range 12” diameter work table These are manual balanced machines – they are typically used for weldments that require quick re-positioning such as boxes, frames, etc. Shipping weight 1300 lbs. Serial #N/A  

P810009 Aronson C-4000 Universal Balance Positioner 4,000 lb. capacity at 12” from the table 360° manual rotation 12” to 84” manual table height range 12” diameter work table These are manual balanced machines – they are typically used for weldments that require quick re-positioning such as boxes, frames, etc. Shipping weight 1300 lbs. Serial #N/A

P810012 Aronson C-4000 Universal Balance Positioner 4,000 lb. capacity at 12” from the table 360° manual rotation 12” to 84” manual table height range 12” diameter work table These are manual balanced machines – they are typically used for weldments that require quick re-positioning such as boxes, frames, etc. Shipping weight 1300 lbs. Serial #N/A


USED PIPE CHUCKS – GRIPPERS

CH812005 Aronson Model 3JC5 3-Jaw Self Centering Scroll Chuck 5” maximum outside clamping capacity 7” maximum inside clamping capacity 1-1/4” thru hole Serial #N/A

CH110420 Aronson Model 3JC24 3-Jaw Chuck 3” – 24” clamping capacity 3 jaw self-centering Serial #N/A

CH404009 Ransome Model 40 Gripper Chuck Self-Centering 3-1/2” to 40” diameter clamping capacity Set of 3 bolt-on jaws Mounting not included Shipping weight 350 lbs. Serial #N/A

CH140408P Cushman Model 15” 3-Jaw Scroll Chuck 3” – 24” clamping capacity 3 jaw self-centering Serial # N/A


USED HEADSTOCK & TAILSTOCKS
 
 

H130909A Aronson Model RHS .5 500 lb. Headstock As-Is 26” fixed height to the center of the rotational axis 360° powered rotation Currently equipped with a servo motor 18” diameter table Shipping weight 150 lbs. Serial #9313

H130910A Aronson Model RHS .5 500 lb. Headstock As-Is 26” fixed height to the center of the rotational axis360° powered rotation 18” diameter table Shipping weight 150 lbs. Serial #9432

H810020 Aronson TS1000 1,000 lb. Manual Special Utility Tailstock 30” to 45” manual adjustable height to the center of the rotational axis 360 ° manual rotation with brake and 45 ° pin lock 8” diameter table Shipping weight 150 lbs. Serial #80683

H810021 Aronson TS1000 1,000 lb. Manual Special Utility Tailstock 30” to 45” manual adjustable height to the center of the rotational axis 360° manual rotation with brake and 45° pin lock 8” diameter table Shipping weight 150 lbs. Serial #76727  

H111010 Kaman Hydraulic 1,000 lb. Headstock 1000 lb. capacity at 6” center of gravity Variable speed 39” to the center of the rotational axis 28”x 42”x 5/8” table Pull handle control 460 volt Shipping weight # 1,500 lbs. Serial # HP924  

H111011 Kaman Hydraulic 1,000 lb. Headstock 1,000 lb. capacity at 6” center of gravity Variable speed 39” to the center of the rotational axis 28”x 42”x 5/8” table Pull handle control 460 volt Shipping weight # 1,500 lbs. Serial #HP950

H100729 Hobart/Motoman 1,000 lb. Headstock  As-Is 1,000 lb. capacity at 6” center of gravity Converted 47” height to the center of the rotational axis 24” diameter round tables Currently equipped with a servo motor Can be converted to a standard operating unit Shipping weight 2,000 lbs. Serial #89142

H100725 Aronson RHS-1.0 1,000 lb. Headstock  1,000 lb. capacity at 6” center of gravity 33” height to the center of the rotational axis 18” diameter round table Variable speed Pendant control for all functions 115 volt Shipping weight 550 lbs. Serial #9510

H100724 Bobcat 1,000 lb. Headstock/Tailstock As-Is 1,000 lb. capacity at 12” center of gravity  Converted 30” height to the center of the rotational axis 12” diameter round tables 85” of space between head and tailstock Currently equipped with a servo motor Can be converted to a standard operating unit Serial #N/A Shipping weight: 1,300 lbs. Shipping dimensions: 11’x3’x5’

H304010 Ardmore 2,000 lb. Headstock/ Tailstock As-Is 2,000 lb. capacity w/pendant 36” height to the center of the rotational axis 13” x 9” table with 4” diameter center hub Body is constructed of 1/2” plate steel 460 volt Serial #N/A  

H304011 Ardmore 2,000 lb. Beam Rotator As-Is 2,000 lb. capacity w/pendant 38 1/2” height to the center of the rotational axis 13 1/2” x 19 1/2” box with manual clamps 2” x 2” minimum 12” x 18” maximum capacity 460 volt Serial #N/A

H110305 Garland 2,500 lb. Headstock 2,500 lb. capacity at 12” center of gravity Variable speed rotation 52” height to center of rotational axis 26-1/2” diameter round table Pendant control for all functions 230 or 460 volt Serial #N/A  

H805023 Irco Model HS-4 4,000 lb. Headstock 4,000 lb. capacity at 6” center of gravity Variable speed rotation from.04 to 1.2 rpm 64” to the center of the rotational axis 42” round table with slots Pendant control 230 or 460 volt Serial # n/a Shipping weight 1,200 lbs. Reconditioned

H150425 Kress 4,000 lb. Headstock 4,000 lb. capacity at 12" center of gravity Constant speed rotation 48" x 48" square table, 3/4" thick Fixed height of 49" to the center of rotational axis, 52-1/2" riser available 460 volt Serial #n/a Shipping dimensions: 8' long x 5' wide x 6-1/2' high Shipping weight: 5,000 lbs. Reconditioned:

H150415 Aronson Model TS-10 10,000 lb. Tailstock  10,000 lb. capacity at 12” center of gravity Fixed height of 36" to the center of the rotational axis 48" square table with slots Shipping weight 3,000 lbs. Shipping dimensions: 6' long x 5' wide x 62.5" high Serial #76123   

H150416 Aronson Model TS-10 10,000 lb. Tailstock  10,000 lb. capacity at 12” center of gravity Fixed height of 36" to the center of the rotational axis 48" square table with slots Shipping weight 3,000 lbs. Shipping dimensions: 6' long x 5' wide x 62.5" high Serial #77125  

H110321 Aronson Model HS-10 10,000 lb. Headstock  10,000 lb. capacity at 12” center of gravity Variable speed rotation from .04 to 1.0 RPM 48” square table with slots 36 1/2” height to the center of the rotational axis 15 1/2” riser Single gearbox Pendant control Shipping weight 5,400 lbs. Serial #7073

H110324 Aronson Model HS-10 10,000 lb. Headstock  10,000 lb. capacity at 12” center of gravity Variable speed rotation from .04 to 1.0 RPM 48” square table with slots 36 1/2” height to the center of the rotational axis 16” riser Dual gearbox Pendant control Shipping weight 2,600 lbs. Serial #95429

H102204 Aronson HS-10 GE, 10,000 lb. “Geared Elevation” Headstock Positioner  Capacity 5 tons at 12” center of gravity from table & center of rotation Variable speed rotation by new AC inverter control Powered geared elevation of 20” to 72” center of rotation from floor 36” diameter round table with 9” thru hole Shipping weight 8,600 lbs. Serial #695

H110304 Garland 10,000 lb. Headstock  10,000 lb. capacity at 12” center of gravity variable speed rotation 40” height to center of rotational axis 27-1/2 “ diameter round table with 3” thru hole Pendant control for all functions 230 or 460 volt Serial #N/A

H100727 Fanuc 10,000 lb. Tailstock 10,000 lb. capacity at 6” center of gravity 44” height to the center of the rotational axis Air pin locks at 180° 6.75” diameter table Serial #N/A  

H100728 Fanuc 10,000 lb. Tailstock 10,000 lb. capacity at 6” center of gravity 44” height to the center of the rotational axis Air pin locks at 180° 6.75” diameter table Serial #N/A

H805002 Irco Model RHS-10 10,000 lb. Headstock  10,000 lb. capacity at 12” center of gravity Variable speed rotation Dual pinion drive Fixed table height of 72” to the center of the rotational axis 40” x 41.25” table Pendant control for all functions 230 or 460 volt Serial #12398  

H110212 Ransome 5H 10,000 lb. Headstock 10,000 lb. capacity at 12” center of gravity Variable Speed .52 RPM constant speed rotation 48” square table with slots 72” to the center of the rotational axis Pendant Control 230 or 460 volt Serial #5313103

H110213 Ransome 5H 10,000 lb. Headstock 10,000 lb. capacity at 12” center of gravity Variable Speed .52 RPM constant speed rotation 36” diameter round table with slots 72” to the center of the rotational axis Pendant Control 230 or 460 volt Serial #N/A

H150412 Aronson Model HTS-12 12,000 lb. Headstock/Tailstock  12,000 lb. capacity at 6” center of gravity Dual pinion drive Variable speed rotation from .05 to 1.5 RPM Fixed height of 36" to the center of the rotational axis 34" round table with a 7" diameter thru hole Pendant control for all functions 460 volt Shipping weight 4,450 lbs. Shipping dimensions: 4' long x 4' wide x 5" high Serial #889/NA

H150413 Aronson Model HTS-12 12,000 lb. Headstock/Tailstock  12,000 lb. capacity at 6” center of gravity Dual pinion drive Variable speed rotation from .05 to 1.5 RPM Fixed height of 36" to the center of the rotational axis 34" round table with a 7" diameter thru hole Pendant control for all functions 460 volt Shipping weight 4,450 lbs. Shipping dimensions: 4' long x 4' wide x 5" high Serial #8810/NA  

H805017 Aronson Model RVTS12/20GE 12,000 lb. Geared Elevation Tailstock Variable Speed Travel Car with Track 12,000 lb. capacity at 6” center of gravity Constant speed powered geared elevation from 57” to 178” to the center of the rotational axis Mounted on a variable speed rack and pinion driven travel car with 46’ of track Pendant control for all functions 230 or 460 volt Serial #N/A

H504001A Komatsu 12,500 lb. Headstock 12,500 lb. capacity at 6" center of gravity Constant speed rotation 55" diameter round table Fixed height of 54" to the center of the rotational axis Pneumatic disc brake for additional safety with off centered loads Serial #JH-381 Shipping weight - 4,650 lbs. Shipping dimensions - 8' long x 5' wide x 7' high  

H805003 IGM System Model RF6000 13,200 lb. Tailstock 13,200 lb. capacity at 6” center of gravity Fixed height of 87” to the center of the rotational axis 59” diameter round table 1988 date of manufacturer Serial #501699

H805004 IGM System Model RF6000 13,200 lb. Tailstock 13,200 lb. capacity at 6” center of gravity Fixed height of 87” to the center of the rotational axis 59” diameter round table 1988 date of manufacturer Serial #501699 

H810019 Aronson TS-16 16,000 lb. Tailstock Fixed height of 50” to the center of the rotational axis 54: square table with slots Shipping weight 2,000 lbs. Serial #N/A

H121019P Ransome/Worthington Model 6H 16,000 lb. Headstock 16,000 lb. capacity at 6” center of gravity .025 to 1.5 IPM variable speed rotation 48” square table with slots 40” fixed height to the center of the rotational axis (can be increased with a riser) Pendant control 460 volt Shipping weight 2,500 lbs. Serial # 54399

H805011 Aronson Model RHS-16 16,000 lb. Headstock 16,000 lb. capacity at 12” center of gravity Variable speed rotation from .02 to .60 RPM Fixed height of 50” to the center of the rotational axis 35” diameter mounting ring - no table Pendant control for all functions 230 or 460 volt Serial #9115  

H909005 Aronson HS-16GE Geared Elevation Headstock 16,000 capacity at 12” center of gravity Variable speed rotation from .02 to .60 RPM by a dual pinion drive Powered geared elevation height from 20” to 72” to the center of the table 36” diameter round table 230 or 460 volt Shipping weight 9,500 lbs Serial #8225  

H508004 Crossroads 90 ° Indexing Headstock/Tailstock 20,000 lb. concentric load capacity To index part from flat to 90° only in one direction and then back to starting position 59” to the center of the rotational axis Electric/hydraulic driven 230/460 volt Input Serial #N/A

H100603 Aronson Model HS-20 20,000 lb. Headstock  20,000 lb. load capacity at 12” center of gravity Variable speed rotation from .016 to .5 RPM 54” square table with slots 50” height to the center of the rotational axis Pendant control Shipping weight 3,600 lbs. Serial #7129

H100605 Aronson Model TS-20 20,000 lb. Tailstock  20,000 lb. load capacity at 12” center of gravity 54” square table with slots 53” height to the center of the rotational axis Shipping weight 2,900 lbs. Serial #N/A

H130203 Pandjiris HTS-200 20,000 lb. Headstock/Tailstock  20,000 lb. capacity Variable speed rotation Headstock and Tailstock both sit on 40’ of track Headstock has 60” diameter slotted table and is fixed Tailstock has 36” height to the center of the rotational axis with live center Tailstock has manual horizontal adjustment using rack and pinion system Pendant control 230 or 460 volt Shipping weight 10,000 lbs. Serial # 25-3793  

H211007 Teledyne Readco 20,000 lb. Headstock/Tailstock 20,000 lb. capacity at 6" center of gravity Variable speed rotation 53" diameter round table with slots Forward/off/reverse foot pedal Headstock is mounted on a screw driven variable speed travel car on 9' of track Tailstock has a 24" diameter through hole Pendant control for all functions Serial #106-633

H100602 Aronson Model TS-25 25,000 lb. Tailstock 25,000 lb. load capacity at 12” center of gravity 60” square table with slots 50” height to the center of the rotational axis Shipping weight 3,100 lbs. Serial #8182

H110909 Pandjiris HTS-300 30,000 lb. Power Elevation Headstock/Tailstock 30,000 lb. capacity  Variable speed rotation 54” Square tables with slots Powered adjustable height from 30” to 108” Pendant control 460 volt Shipping weight 30,000 lbs. Serial #41-0091-2

H912005 Ransome Model 6H/6T 32,000 lb. Headstock/Tailstock 32,000 lb. capacity at 6” center of gravity Constant speed rotation of .56 RPM (can be converted to variable speed) 54” square tables with slots 78” height to the center of the rotational axis Tailstock is mounted on a constant speed travel car that runs on 46” machined 60 lb. RR track (Not Supplied) 460 volt Serial #6933357/6933359  

H904003 Aronson HTS-40 40,000 lb. Headstock/Tailstock 40,000 lb. capacity at 6” center of gravity Variable speed rotation from .026 to .8 RPM Dual pinion drive 36.5” round tables with a 19” diameter thru hole 50” height to the center of the rotational axis Pendant control 230 or 460 volt Shipping weight 6,500 lbs. Serial #N/A

H909001 Aronson HTS-40 40,000 lb. Headstock/Tailstock 40,000 lb. capacity at 6” center of gravity Variable speed rotation from .026 to .8 RPM Dual pinion drive 36.5” round tables with a 19” diameter thru hole 50” height to the center of the rotational axis Pendant control 230 or 460 volt Shipping weight 6,500 lbs. Serial #861

H909002 Aronson HTS-40 40,000 lb. Headstock/Tailstock 40,000 lb. capacity at 6” center of gravity Variable speed rotation from .026 to .8 RPM Dual pinion drive 36.5” round tables with a 19” diameter thru hole 50” height to the center of the rotational axis Pendant control 230 or 460 volt Shipping weight 6,500 lbs. Serial #862

H909003 Aronson HTS-40 40,000 lb. Headstock/Tailstock 40,000 lb. capacity at 6” center of gravity Variable speed rotation from .026 to .8 RPM Dual pinion drive 36.5” round tables with a 19” diameter thru hole 50” height to the center of the rotational axis Pendant control 230 or 460 volt Shipping weight 6,500 lbs. Serial #863  

H110340 Worthington Model 7H/7T 48,000 lb. Headstock/Tailstock 48,000 lb. capacity at 6” center of gravity .025 to 1.5 IPM variable speed rotation 53” square table with slots 50” fixed height to the center of the rotational axis (can be increased with a riser) Pendant control 230/460 volt Shipping weight 9,150 lbs. Serial # 59/56194

H110341 Worthington Model 7H/7T 48,000 lb. Headstock/Tailstock 48,000 lb. capacity at 6” center of gravity .025 to 1.5 IPM variable speed rotation 53” square table with slots 50” fixed height to the center of the rotational axis (can be increased with a riser) Pendant control 230/460 volt Shipping weight 9,150 lbs. Serial #55536/53900  

H120840C Aronson 120 Ton Headstock/Headstock Rotator 120 ton capacity at 6” center of gravity 292” to center of rotating axis 688” between headstocks Variable speed rotation from .004-.40 RPM Headstocks are both powered and synchronized with wireless remote Center section was used to rotate truck beds 575 volt 3 phase Serial # 45826


USED WELDING TURNTABLES

FT120305 Unique/Readco 2,000 lb. Floor Turntable 2,000 lb. capacity Variable speed rotation from 0.1 – 6.0 RPM by a 10 turn potentiometer 15 1/2 “ working height” 34” diameter round table with slots Pendant control 230 volt 1 phase Shipping weight 1,000 lbs. Serial #101931

FT140108 Keystone 2,000 lb. Turntable 2,000 lb. capacity Variable speed rotation .03-3.4 RPM Fixed height at 9 1/2” 24” round table with T-slots Pendant control for all functions 230 volt 1 phase Serial #879912

TI005005 Hercules 2,000 lb. Power Tilting Tables Model TI-23842 38” X 42” table w/16” lip electro-hydraulic tilt of approximately 75° 115 volt input Serial #N/A

TT306001 Advanced Lifts 2,000 lb. Power Tilting Table Model UE-290 54" long x 48" wide two sided table Electric/hydraulic tilt of 90° 208/230/460 volt 3 phase Serial #23497/1199

FT 140109 Ransome Model 25-P 2,500 lb. Turntable 2,500 lb. capacity at 12” center of gravity Variable speed rotation .03-3.4 RPM Fixed height at 25 1/2” 42” x 3/4” round slotted table Pendant control for all functions 230 or 480 volt 3 phase Serial # 879912

FT150508 Worthington Model 160 16,000 lb. floor turntable 16,000 lb. capacity @ 12" Variable speed rotation Fixed height of 39" 70" round table 15" pendant control 460 volt Shipping dimensions: 6' long x 6' wide x 4' Shipping weight: 5,000lbs  Reconditioned:

FT405002P VMW 100 Ton Floor Turntable 200,000 lb. capacity at 12" center of gravity Variable speed drive with forward and reverse 10' diameter round table with a fixed height of 48" Pendant control Serial #N/A


USED TURNING ROLLS

T120203 Caterpillar 3,000 lb. Unit Frame Turning Rolls 3,000 lb. weight capacity 3” to 26” diameter capacity Constant speed rotation 2 1/2” wide x 11 1/2” diameter rubber wheels 2 powered wheels are 23 1/2” to top of wheels 2 idler wheels are 25” high to the top of the wheels Custom built for the welding of cone shapes 230/460 volt Serial #N/A

T120804P Reynolds 3,000 lb. Unit Frame Turning Rolls 3,000 lb. weight capacity 10” to 4’ diameter capacity Variable speed rotation 2 1/2” wide x 10” diameter rubber wheels 6” minimum 148” maximum length capacity Rollers on each end to keep work piece aligned 460 volt Serial #N/A

T120806 Reynolds 3,000 lb. Unit Frame Turning Rolls 3,000 lb. weight capacity Variable speed 36” to 48” diameter capacity Constant speed rotation 2 1/2” wide x 10” diameter rubber wheels 10” minimum - 240” maximum length capacity 110 volt Serial #N/A

T405001 Radian 3,000 lb. Turning Rolls Drive Roll with Idler Converted to Variable Speed w/ Pendant 3,000 lb. total weight capacity 16" diameter x 4" wide rubber tires Overload discs Constant speed friction drive rotation 4" minimum to 36" maximum diameter capacity 230/460 volt Serial #N/A  

T405002 Radian 3,000 lb. Turning Rolls Drive roll with idler Converted to Variable Speed w/ Pendant 3,000 lb. total weight capacity 16" diameter x 4" wide rubber tires Overload discs Constant speed friction drive rotation 4" minimum to 36" maximum diameter capacity 230/460 Volt Serial #N/A

T701005 Pandjiris Super Piper 10/5 Steel Wheel Turning Rolls Drive and idler Variable speed drive from 9 to 180 IPM 10,000 lb. load capacity 10" to 48" diameter capacity Variable speed from 2.0 to 60 IPM 2-1/2" wide x 12" diameter steel wheels on both the drive and idler Pendant Control Serial #N/A

T130610 Custom 4,000 lb. Turning Rolls Drive and idler 4,000 lb. load capacity 6" to 20" diameter capacity Variable speed from 1.5 to 45 IPM 3-1/2" wide x 12" diameter rubber wheels on both the drive and idler 18’ V-track for idler to roll on for easy manual length adjustment Both drive and idler have risers to for a 36” height for work piece Pendant Control Foot Pedal Serial #N/A  

T100539 Riley 2 Ton Steel Wheel Idler Roll 4,000 lb. weight capacity 3” to 72” diameter capacity 8” diameter x 2.25” wide steel wheels Serial #N/A  

T100540 Riley 2 Ton Steel Wheel Idler Roll 4,000 lb. weight capacity 3” to 72” diameter capacity 8” diameter x 2.25” wide steel wheels Serial #N/A

T976004 Worthington Type A 4,000 lbs. Driver Only 15” dia. X 3” wide rubber faced rolls Variable speed 12,000 lbs. turning capacity Serial #N/A

T130710 Pandjiris Tanker TIR-40 4,000 lb. Tanker Idler Roll 4,000 lb. weight capacity 4” to 144” diameter capacity Single rubber wheels No wheel adjustments necessary for the full range of diameters & tankers maintain a constant center line Shipping weight 350 lbs. Serial #N/A

PRO-TR50000U Profax 5,000 lb. Turning Rolls 5,000 lb. weight capacity Minimum work diameter 4” Maximum work diameter 48” Wheel: diameter 10”, width 3” 1/8 horsepower 0-4 RPM Serial # TR5-2865-DU TR5-2502-DU Shipping weight drive and idler 430 lbs. Factory reconditioned – 2 sets available  

T205002A Teledyne-Readco TRR-50, 5,000 Turning Roll Set Variable speed ½ HP 115 volt Pendant control of 2.5 to 75 IPM 9” diameter x 4” wide rubber wheels For diameters from 3” to 10’ Serial #N/A

T303003A Aronson WRI-5 5,000 lb. Idler 5,000 lb. weight capacity
6” to 6’ diameter capacity 12” diameter x 4” wide rubber wheels Shipping weight 200 lbs. Serial #N/A


T711011 Aronson WRI-5 5,000 lb. Idler Roll 5,000 lb. weight capacity
6” to 12’ diameter capacity Idler only Shipping weight 450 lbs. Serial #N/A

T120808 Worthington Model AIRR 2 1/2 Ton Turning Roll Idler Idler Only 5,000 lb. weight capacity 5” to 12’ diameter capacity 2 1/2” wide x 16” diameter rubber wheels Serial #N/A

T 140201A Ransome AIRR Idler As is 5,000 lb. weight capacity 12” to 12' diameter capacity 11 1/4” diameter x 3” wide steel wheels Serial #N/A

T100536 Aronson Model WSU-5 5,000 lb. Steel Wheel Unit Frame Turning Roll 5,000 lb. weight capacity 148” bed length 3” to 24” diameter capacity Variable speed from 2 to 50 IPM 12” diameter x 4” wide steel wheels Pendant control 230 or 460 volt Serial #7341

T810028 Cayuga 5,000 lb. Power Elevation Unit Frame Roll 5,000 lb. weight capacity 24” minimum length capacity 30” to 72” diameter capacity Variable speed travel Powered elevation from 36” to 48” to the top of the wheels 12” diameter x 3” wide rubber wheels 230 or 460 volt Serial #28A86

T100909 Cecil Peck 5,000 lb. Unit Frame Turning Rolls with Hold down Device 5,000 lb. weight capacity 8” to 42” diameter capacity Variable speed rotation 5” wide x 9” diameter rubber wheels 2 wheels per shaft 1 shaft is powered the other is an idler 40.5” high to the top of the wheels Custom built for the welding of pipe “tees” and elbows 115 volt On/Off foot pedal Serial #N/A

T130103 Preston-Eastin Model UFTRA 5/36 5,000 lb. Unit Frame Turning Rolls 5,000 lb. weight capacity As is 6” to 36” diameter capacity Variable speed rotation 4 1/2” wide x 12” diameter rubber wheels 2 wheels per shaft 1 shaft is powered the other is an idler 40.5” high to the top of the wheels Pendant control for all functions 115 volt Shipping weight 800 lbs. Serial # UFTRA 5/36-32

T130103A Custom Preston-Eastin Style Idler Roll 5,000 lb. Unit Frame Idler Roll 5,000 lb. weight capacity 8” to 42” diameter capacity Variable speed rotation 6” wide x 12” diameter rubber wheels 2 wheels per shaft 40.5” high to the top of the wheels Shipping weight 475 lbs. Serial #N/A

T405003 Radian 5,000 lb. Turning Rolls  Drive roll with idler Variable Speed 5,000 lb. total weight capacity 16" diameter x 1" wide steel wheels Overload discs Constant speed chain drive rotation 4" minimum to 36" maximum diameter capacity 230/460 volt Serial #N/A  

T130709 Pandjiris Tanker TPR- 80/TIR-40 8,000 lb. Tanker Turning Roll Set 8,000 lb. weight capacity per set 4” to 144” diameter capacity Additional Idler Variable speed from 2.9 to 72 IPM lbs./set Single rubber wheels No wheel adjustments necessary for the full range of diameters and tankers maintain a constant center line 25’ pendant control 115 volt Shipping weight 1,200 lbs. Serial # 800-9851-1/800-9852-3

T130902A Pandjiris Model IR-6 3 Ton Idler Roll Only 6,000 lb. weight capacity 8” to 12’ diameter capacity Two 20” diameter x 5” wide rubber wheels per end Serial #41-0631-4 Shipping weight 300 lbs. Serial #N/A  

T140309P Aronson Model WSI 10 5 Ton Idler Roll 10,000 lb. weight capacity 6” to 48” diameter capacity 4” wide x 12” diameter steel wheels Serial #90140  

T130605 Cecil Peck 5 ton Turning Rolls Drive and idler 10,000 lb. weight capacity per set 12” to 84” diameter capacity Variable speed from 2.1 to 63.5 IPM 28” diameter x 4” wide rubber wheels Pendant control 230/460 Volt Serial #N/A

T120811 Ransome Model AAPRR 5 Ton Turning Roll Drive As-Is Drive Only. 10,000 lb. weight capacity 5” to 12’ diameter capacity 5” wide x 16” diameter rubber wheels Variable speed by Reeves drive 480 volt Serial #N/A

T120807 Ransome Model APRR/AIRR 5 Ton Turning Roll Set  Drive and Idler 10,000 lb. weight capacity Add an additional idler for a total capacity of 15,000 lb. 5” to 12’ diameter capacity 2 1/2” wide x 16” diameter rubber wheels Variable speed rotation from 1.45 to 58 IPM Pendant control 230 or 460 volt Serial #N/A

T405007 Radian 10,000 lb. Turning Rolls Drive roll and idler Variable Speed w/Pendant 10,000 lb. total weight capacity 16" diameter x 3.5" wide rubber wheels Constant speed rotation 4" minimum to 144" maximum capacity 230/460 volt Serial #N/A  

T209003 Aronson Model WPS4WD101-18 4-Wheel Drive Unit Frame Pipe Turning Roll "1995" 10,000 lb. capacity 18" frame length 24" to 54" diameter capacity 15" diameter x 2.5" wide steel wheels Variable speed from 2.0 to 50 IPM Pendant control Used for Overlaying of Short Steel Mill Rolls Serial #9580

T810025 Aronson WRD-10C Drive Roll 10,000 lb. weight capacity 30,000 lb. turning capacity 12” to 6’ diameter capacity Variable speed from 2 to 50 IPM 20” diameter x 5” wide rubber wheels with overload discs Shipping weight 900 lbs. Serial #72033

T508003 Worthington “A” 10,000 lb. Turning Rolls As-Is Drive and idler 10,000 lb. weight capacity 5” to 72” diameter capacity Variable speed rotation from 6.1 to 61 IPM by a sheave drive 16” diameter x 3” wide rubber wheels On/off pendant 230/460volt Serial #N/A

T130607 Aronson Model WRI 10 5 Ton Idler Roll 10,000 lb. weight capacity 6” to 13’ diameter capacity 4” wide x 12” diameter rubber wheels w/overload discs Serial #N/A

T130715 Pandjiris Model IR-10 5 Ton Idler Roll Only 10,000 lb. weight capacity 6” to 15’ diameter capacity Variable speed from 5.3 to 53 IPM 16” diameter x 4” wide rubber wheels Serial #N/A

T120106 Pandjiris Tanker 150 15,000 lb. Tanker Turning Roll Set ** PARTS ONLY **** 15,000 lb. weight capacity 3.5” to 12’ diameter capacity Variable speed from 2.9 to 72 IPM lbs./set Single rubber wheels No wheel adjustments necessary for the full range of diameters and Tankers maintain a constant center line 25’ pendant control 115 volt Serial #N/A Shipping weight 1,200

T130608 Aronson Model WRD 15 7.5 Ton Drive Roll 15,000 lb. weight capacity 6” to 13’ diameter capacity Two 4” wide x 12” diameter rubber wheels w/overload discs per axle Variable speed rotation from 1.45 to 58 IPM Pendant control 230 or 460 volt Serial # 9680

T140307 Pandjiris Missouri Mule 15/5 Steel Wheel Turning Rolls Drive and idler 20,000 lb. weight capacity per set Add an additional idler for a total capacity of 30,000 lb. 4” to 12’ diameter capacity Variable speed from 2.1 to 63.5 IPM 16” diameter x 4” wide steel wheels 6' x 11' steel base plate with track for easy work piece length adjustment Pendant control and forward/stop/reverse foot pedal 460 volt Serial #10934X22-5  

T130711 Pandjiris Missouri Mule 15/5 Turning Rolls Drive and idler Additional Idler 20,000 lb. weight capacity per set Add an additional idler for a total capacity of 30,000 lb. 4” to 12’ diameter capacity Variable speed from 2.1 to 63.5 IPM 16” diameter x 4” wide rubber wheels Pendant control 460 volt Serial #N/A Ship Weight. 1,550 lbs./set

T120810 Aronson Model WRD/WRI 10 Ton Turning Roll Set includes drive and idler 20,000 lb. weight capacity Add an additional idler for a total capacity of 30,000 lb. 5” to 12’ diameter capacity 4” wide x 12” diameter rubber wheels w/overload discs Variable speed rotation from 1.45 to 58 IPM Pendant control 230 or 460 volt Serial #N/A

T130606 Aronson Model WRD/WRI 10 10 Ton Turning Roll Set includes drive and idler 20,000 lb. weight capacity Add an additional idler for a total capacity of 30,000 lb. 6” to 13’ diameter capacity 4” wide x 12” diameter rubber wheels w/overload discs Variable speed rotation from 1.45 to 58 IPM Pendant control 230 or 460 volt Serial # 96958/61253

T130123 Preston-Eastin Model TDRA/TIRA 10H 10 Ton Turning Roll Set includes drive and idler 20,000 lb. weight capacity Add an additional idler for a total capacity of 30,000 lb. 6” to 72”diameter capacity 4” wide x 12” diameter rubber wheels w/overload discs Drive roll has 26 1/2” riser and Idler roll has a riser with V-groove wheels to roll on track for easy length adjustment Variable speed rotation from 1.45 to 58 IPM Pendant control 230 or 460 volt Serial #TIRP 101 D 96

T100537 Riley 10 Ton Steel Wheel Idler Roll 20,000 lb. weight capacity 16” to 10’ diameter capacity 12.5” diameter x 9.5” wide steel wheels Serial #N/A

T100545 Riley 10 Ton Steel Wheel Idler Roll 20,000 lb. weight capacity 16” to 10’ diameter capacity 12.5” diameter x 9.5” wide steel wheels Serial #N/A

T704013 Aronson Model WRD-20 20,000 lb. Drive Roll Only 20,000 lb. weight capacity 60,000 lb. turning capacity 6" to 13’ Diameter capacity 12" diameter x 13-3/8" rubber wheels Variable speed from 2.0 to 50 IPM 480 volt 1 phase Serial #83440

T100532P Ransome BPRR 15 30,000 lb. Drive Roll Only 15 Ton set down weight capacity 45 ton turning capacity 8” to 8’ diameter capacity 7” wide x 20” diameter rubber wheels Variable speed from 1.5 to 59 IPM 230 or 460 volt Serial #352494

T100533P Ransome BPRR 15 30,000 lb. Drive Roll Only 15 Ton set down weight capacity 45 ton turning capacity 8” to 8’ diameter capacity 7” wide x 20” diameter rubber wheels Variable speed from 1.5 to 59 IPM 230 or 460 volt Serial #N/A

T100534P Worthington BPRR 15 30,000 lb. Drive Roll Only 15 Ton set down weight capacity 45 ton turning capacity 8” to 10’ diameter capacity 7” wide x 20” diameter rubber wheels Variable speed from 1.5 to 59 IPM 230 or 460 volt Serial #N/A

T901001 Ransome BPRR 30,000 lb. Drive Roll Only 15 Ton set down weight capacity 45 ton turning capacity 8” to 8’ diameter capacity 7” wide x 20 1/2” diameter rubber wheels Variable speed from 1.5 to 59 IPM 230 or 460 volt Serial #N/A

T111110 Ransome Model BIRR 15 Ton Idler Roll Only **Parts ONLY** 30,000 lb. weight capacity 7” to 16’ diameter capacity 7” x 22” diameter rubber wheels Serial #N/A

T808002 Ransome SA-15PR/SA-7.5IR “Rustler” 15 Ton Turning Roll Set  includes drive and idler Automatically adjust to take any circular piece from 12” to 10’ diameter 30,000 lb. weight capacity 12” diameter x 3.5” wide rubber wheels Variable speed travel from 4.8 to 48 IPM Pendant control 230 or 460 volt Shipping weight 2,400 lbs. Serial #7925369/8025370

T120402P Ransome SA-15PR/SA-7.5IR “Rustler” 15 Ton Turning Roll Set  includes drive and idler Automatically adjust to take any circular piece from 12” to 10’ diameter 30,000 lb. weight capacity 12” diameter x 3.5” wide rubber wheels Variable speed travel from 4.8 to 48 IPM Pendant control 230 or 460 volt Serial #N/A Shipping weight 2,400 lbs.

T130901A Pandjiris Model PR-100 17 Ton Drive Roll Only 34,000 lb. weight capacity 12” to 21’ diameter capacity Two 12” Diameter x 4” wide rubber wheels per end 480 volt Serial #25-1956-8 Shipping weight 3,000 lbs.

T150902P Webb Model R-500 40,000 lb. turning roll set Set includes 1 R-500 drive and 1 I-500 idler Add extra idler for 50,000 lb. capacity 18” diameter rubber wheels 1 wheel per axle with a wheel face of 7” For diameters from 6” to 15’ Variable speed from 7 to 58 IPM 30' remote pendant control 460 volt Shipping weight 3,050 lbs./set Shipping Dimensions - 12' Long x 5' Wide x 2' High Serial #2011-140/2011-142  

T110917 Aronson Model WSI-40 20 Ton Idler Only 40,000 lb. weight capacity 30” to 18’ diameter capacity 7” wide x 20” diameter steel wheels Serial #N/A Shipping weight 2,000 lbs.

T150512 Unique-Weldco Model TPS90-30/TIS90-30 30 Ton Steel Wheel Turning Rolls 60,000 lb. weight capacity, add an additional idler for a capacity of 90,000 lbs. 2 additional idlers available (T150513) 6" to 18' diameter capacity Variable speed drive 4" wide x 20" diameter steel wheels 30' pendant control 460 volt Serial #109151/109152 Shipping dimensions: 10' long x 5' wide x 24"high Shipping weight: 3,200 lbs.

T150513 Unique-Weldco Model TIS90-30 30 Ton Steel Wheel Idler Rolls 30,000 lb. weight capacity 6" to 18' diameter capacity 4" wide x 20" diameter steel wheels Serial #109153 and 109154 Shipping dimensions: 8'6" long x 24" wide x 24"high Shipping weight: 1,200 lbs.  

T121018 Aronson Model WRD/WRI 30 Ton Turning Roll Setincludes drive and idler 60,000 lb. weight capacity 90,000 capacity with second idler 8” to 72” diameter capacity Variable speed from 2 to 50 IPM 20” diameter x 7” wide rubber wheels with overload discs Turning rolls are mounted on 58 1/2 GA rail cars 1 drive and 1 idler Pendant control 230 or 460 volt Serial #N/A

T110920 Ransome Model EIRS 30 Ton Idler Only 60,000 lb. weight capacity 7” to 20’ diameter capacity 14” wide x 20 1/2” diameter rubber wheels Serial #N/A Shipping weight 3,400 lbs.  

T901019 Ransome Model CPRR 30 Ton Drive Roll Only 60,000 lb. weight capacity 180,000 lb. turning capacity 7” to 20’ diameter capacity 14” wide x 20” diameter rubber wheels Variable speed rotation from 1.45 to 58 IPM Pendant control 230 or 460 volt Serial #1305

T110921 Ransome Model CPRS 30 Ton Drive Roll Only 60,000 lb. weight capacity 180,000 lb. turning capacity 12” to 20’ diameter capacity 6”wide x 20 1/2” (x3) diameter steel wheels Constant speed rotation Pendant control 230 or 460 volt Serial #N/A

T901011 Aronson Model WRI-60 30 Ton Idler Only 60,000 lb. weight capacity 8” to 18’ diameter capacity 12” wide x 20” diameter rubber wheels Serial #N/A Shipping weight 2,400 lbs.

T901012 Aronson Model WRI-60 30 Ton Idler Only 60,000 lb. weight capacity 8” to 18’ diameter capacity 12” wide x 20” diameter rubber wheels Serial #N/A Shipping weight 2,400 lbs.

T111113 Pandjiris Model IR-60 30 Ton Idler Roll Only 60,000 lb. Weight capacity 12” to 20’ Diameter capacity Variable speed from 5.3 to 53 IPM 20” diameter x 15” wide rubber wheels Serial #N/A

T901021 Pandjiris Unit Frame 34 Ton Turning Rolls on Variable Speed Travel Car 68,000 lb. turning capacity
7’ to 14’ diameter capacity with a fixed axel center of 72” Variable speed rotation 5 sets of 5” wide x 20” diameter rubber wheels spaced over the 30’ length of a variable speed travel car that runs on 69” gauge rail track Pendant control Serial # 60-4595

T901022 Pandjiris Unit Frame 34 Ton Turning Rolls on Variable Speed Travel Car 68,000 lb. turning capacity 7’ to 14’ diameter capacity with a fixed axel center of 72” Variable speed rotation 5 sets of 5” wide x 20” diameter rubber wheels spaced 30’ over the length of a variable speed travel car that runs on 69” gauge rail track Pendant control Serial #N/A

T110101C Ransome Model DIRR 45 Ton Close Coupled Idler Roll 90,000 lb. capacity 22” diameter x 20” wide rubber tires 10” to 20” diameter capacity Serial #407649

T110919 Pandjiris Model IR-90 45 Ton Idler Only 90,000 lb. Weight capacity 12” to 12 1/2’ diameter capacity 20” diameter x 20” wide rubber wheels w/ overload discs Serial #N/A

T140310P Worthington Model CPRS/CIRS 60 Ton Turning Roll Set 120,000 lb. weight capacity 180,000 lb. turning capacity 7” to 10’ diameter capacity 16” wide x 16” diameter steel wheels Variable speed rotation Pendant control 460 volt Serial # 44121066

T121217 Ransome SA-60PR/SA-30IR 60 Ton Turning Roll Set As-Is Set includes drive and idler These rolls automatically adjust to take any circular piece from 18” to 17’ diameter 120,000 lb. Weight capacity 20.5” diameter x 7” wide rubber wheels Variable speed travel from 5.0 to 50 IPM Pendant control 460 volt Shipping weight 7,800 lbs. Serial # 796341

T111107 Pandjiris Model PR180/60 Turning Rolls Set includes drive and idler Extra Idler 120,000 lb. weight capacity Weight capacity can be increased to 180,000 lb. with extra idler 12” to 20’ diameter capacity Variable speed from 5.3 to 53 IPM 20” diameter x 15” wide rubber wheels Pendant control 230 or 460 volt Serial #N/A

T110916 Ransome Model CPRR/CIRR 60 Ton (Fit-Up) Turning Roll Set  120,000 lb. weight capacity Variable Speed 180,000 lb. turning capacity 7” to 20’ diameter capacity. 14” wide x 20” (x3) diameter rubber wheels Constant speed rotation Pendant control 230 or 460 volt Serial # 6620037/6720039

T110925 Ransome Model EPRR 60 Ton Drive Only 120,000 lb. weight capacity 360,000 lb. turning capacity 7” to 20’ diameter capacity 30” wide x 20 1/2” diameter rubber wheels Constant speed rotation Pendant control 230 or 460 volt Serial #N/A  

T110928 Ransome Model EPRS 60 Ton Drive Only 120,000 lb. weight capacity 360,000 lb. turning capacity 12” to 20’ diameter capacity 6” wide x 22” diameter steel wheels Constant speed rotation Pendant control 230 or 460 volt Serial #N/A

T110924 Ransome Model EIRR 60 Ton Idler Only 120,000 lb. weight capacity 12” to 20’ diameter capacity 30” wide x 20 1/2” diameter rubber wheels Serial #N/A Shipping weight 3,400 lbs.  

T110927 Ransome Model EIRR 60 Ton Idler Only 120,000 lb. weight capacity 12” to 20’ diameter capacity 30” wide x 20 1/2” diameter rubber wheels Serial #N/A Shipping weight 3,400 lbs.  

T901003 Ransome Model DPRRPT/DIRRPT 90 Ton Turning Roll Set 180,000 lb. capacity 4’ to 10’ diameter capacity 16” wide x 42” diameter foam filled rubber truck tires Pendant control 460 volt Serial #3931611/4031261

T901004 Ransome Model DPRRPT/DIRRPT 90 Ton Turning Roll Set  180,000 lb. capacity 4’ to 10’ diameter capacity 16” wide x 42” diameter foam filled rubber truck tires Pendant Control 460 volt Serial #3931612/4031615

T901005 Ransome Model DPRRPT/DIRRPT 90 Ton Turning Roll Set  180,000 lb. capacity 4’ to 10’ diameter capacity 16” wide x 42” diameter foam filled rubber truck tires Pendant Control 460 volt Serial #3931253/4032376

T901006 Ransome Model DPRRPT/DIRRPT 90 Ton Turning Roll Set 180,000 lb. capacity 4’ to 10’ diameter capacity 16” wide x 42” diameter foam filled rubber truck tires Pendant Control 460 volt Serial #NA/4033765

T901007 Ransome Model DPRRPT/DIRRPT 90 Ton Turning Roll Set  180,000 lb. capacity 4’ to 10’ diameter capacity 16” wide x 42” diameter foam filled rubber truck tires Pendant Control 460 volt Serial #N/A

T901008 Ransome Model DPRRPT/DIRRPT 90 Ton Turning Roll Set  180,000 lb. capacity. 4’ to 10’ diameter capacity 16” wide x 42” diameter foam filled rubber truck tires Pendant Control 460 volt Serial 3933763/4033766

T605019 Teledyne-Readco 150 Ton Turbine Rolls 150 ton weight capacity 4” to 48” diameter capacity Variable speed drive from 0 to 48 IPM 23-1/2” diameter x 16” wide rubber wheels Drive and idler Serial #105839/105840

T131005 Ransome Model 200PRS/200IRS 200 Ton Turning Roll Set 400,000 lb. capacity 18” to 20’ diameter capacity 7” wide x 22” steel wheels Variable speed .4-40 IPM Pendant control 460 volt Serial #4218152

T131006 Tulsa Model 200 Ton Hydraulic Turning Roll Set 400,000 lb. capacity 2' to 22’ diameter capacity Variable speed 7” wide x 22” steel wheels 60 GA. manual rail cars on both the drive and idler for easy length adjustment Pendant control Hydraulic/460 volt Serial # 20141

T131007 Braden Model 250 Ton Hydraulic Turning Roll Set 500,000 lb. capacity 18” to 20’ diameter capacity Variable speed 7” wide x 25” steel wheels 60 GA. manual rail cars on both the drive and idler for easy length adjustment Pendant control Hydraulic/460 volt Serial # 51164  


USED MANIPULATORS

M409001 Model H-600 26” x 48” Used Lincoln Manipulator Constant speed power reach from 24” to 50” Screw driven constant power elevation from 12” to 60” Lincoln dc-600 power supply and a NA-5 submerged arc control and head Lincoln manual horizontal and vertical adjusters All mounted on a variable speed travel car with 40’ of track Serial # W7702-0270

M150401 Pandjiris Model 1600 fixed height manipulator with travel car Fixed height of 84" to the bottom of the boom 1,100 lb. capacity either or both ends 3 to 116 IPM variable speed reach from 40" to 196" from the center of the mast Mounted on a manual travel car that runs on 112" wide track (not included) 460 volt Shipping weight 7,450 lbs. Shipping dimensions: 21' long x 9.5' wide x 10.5" high Serial #25-3702

M130611 Capital Model 4’ x 2’ Manipulator/Travel Car 4’ constant speed powered lift from 36” to 84” with 22” travel car riser Manual reach from 8” to 32” from the center of mast rotation Manual king pin base Manual v-groove wheel travel car riser 115 volt Serial #N/A

M130612 Capital Model 4’ x 2’ Manipulator/Travel Car  4’ constant speed powered lift from 36” to 84” with 22” travel car riser Manual reach from 8” to 32” from the center of mast rotation Manual king pin base Manual v-groove wheel travel car riser 115 volt Serial #N/A

M130613 Capital Model 4’ x 4’ Manipulator/Travel Car 4’ constant speed powered lift from 32” to 80” with 10” travel car riser Manual reach from 10” to 58” from the center of mast rotation Manual king pin base Manual v-groove wheel travel car riser 115 volt Serial #N/A

M606017 Ransome Model 44 4’ x 4’ Manipulator / Travel Car 4’ constant speed powered lift from 25” to 73” Manual reach from 9” to 57” from the center of mast rotation Manual king pin base Manual travel car 115 volt Serial #0526806

M130102 Ransome Model 44 4’ x 4’ Manipulator 4’ constant speed powered lift from 32” to 80” Reconditioned Manual reach from 9” to 57” from the center of mast rotation 150 lb. Capacity at either or both ends Reconditioned w/existing equipment Manual king pin base Manual travel car 4” vertical and 2” horizontal manual slides Lincoln na-3n submerged arc welding system · Welding equipment not included 115 volt Shipping weight 1,850 lbs. Serial # 0525908

M121207 Aronson Model 44 4’ x 4’ Manipulator / Travel Car 4’ constant speed powered lift from 25” to 73” Reconditioned Manual reach from 9” to 57” from the center of mast rotation 150 lb. Capacity at either or both ends Manual king pin base Manual travel car 2” vertical and 2” horizontal manual slides · Welding equipment not included 115 volt Serial # 7934-MKMT  

M140304P Ransome Model 99 54” x 54" Manipulator 54” manual Lift from 56” to 110” to the center of the boom to floor 54” variable speed powered reach from 51” to 105” to the center of the mast 360° manual rotation 500 lb. capacity 60” x 90” steel base Miller cladding system System includes: Miller Automatic A1D-DW control, A1D-4L 2 roll feeder, and 60 MM strip head and spool holder 15” Vertical powered slide 3” vertical manual slide for fine adjustment 2 manual head adjusters and 360° swivel 115 volt Serial #N/A · Reconditioned 230 or 460 Volt

M908003P Ransome Model 1212 4’ x 8’ Manipulator and Travel Car with Track 4’ constant speed lift from 57.75” to 105.75” 1 to 62 IPM variable speed reach from 27” to 122” 360° manual mast rotation 5 to 200 IPM Variable speed travel car that runs on 70’ (2 sections 20’, 3 sections 10’) of 33 gauge track Currently equipped with 4 Lincoln DC-600 power supplies 2 Lincoln NA-3N controls with feed heads Vertical and horizontal adjusters for each weld head all mounted on manual spotting cars mounted on the manipulator boom and an Invincible flux recovery system 230 volt Serial #629592

M140910 Pandjiris 4’x10’ Model 1600 Welding Manipulator Manipulator Only 750 lb. weight capacity either or both ends Constant speed Powered lift from 28” to 76” to the bottom of the boom No rotation Solid 36” round floor mount 3” to 116” IPM powered reach 32” to 152” from the center of the mast 6”x6” powered heavy duty slides Dual Linde 2 roll feeders and controls 460 volt, 3-phase Serial #600-4394-2 Shipping dimensions: 18’Lx8’Wx5’H Shipping weight: 8,000 lbs. Note: Needs gear rack added

M140909 Pandjiris/Ransome 4’x16’ Model 1400 Welding Manipulator 500 lb. weight capacity either or both ends Constant speed Powered lift from 32” to 80” to the bottom of the boom No rotation Solid 36” round floor mount 3” to 116” IPM variable speed 32” to 224” from the center of the mast L-Tec 2 roll feeder and control 4” manual slide 460 volt, 3-phase Serial #600-4394 Shipping dimensions: 22’Lx8’Wx5’H Shipping weight: 9,000 lbs.

M411001 Custom 5 x 6 Manipulator Fixed Boom Manipulator
360° of rotation 6’ of horizontal travel w/Linde style carriage and 60” of vertical travel from 31” to 91” by a Screw Driven manual hand wheel lift

M140303P Herrick 5’ x 7’ Manipulator 5’ constant speed power lift from 24” to 84” to the center of the boom 7’ variable speed power reach of 1.8 to 180 IPM from 15” to 99” from the center of the mast 250 lb. weight capacity 360° manual rotation on 5' x 5' free standing Base has level adjustment screws at all four corners Miller submerged-arc weld system: automatic 2 control, A2-4L 4 roll two speed feeder and flux hopper Pendant control Serial # 72-8031

M404010 Ransome Model 99 6’ x 4’ Manipulator 6’ constant speed powered lift from 36” to 108” Fixed boom with powered carriage Carriage travel is 44” to 92” from the center of mast rotation 500 lb. capacity 5' x 13' base with power supply mount 460 volt Serial #9526552

M140401P Cayuga 6’ x 4’ Manipulator/Travel Car  6’ constant speed power lift at 34 IPM from 19 1/2” to 91 ½” to the center of the boom 4’ variable speed power reach of 1.8 to 180 IPM from 13” to 61” from the center of the mast 250 lb. weight capacity 360° manual rotation on variable speed travel car with dual tank rack Jetline HWF-200D/CWF-10A wire feed system Jetline HWF-200D Hot wire power supply and 9302B control ALC 101 Arc length control system with 6” powered vertical slide Thermal Dynamics plasma welding system: PS-3000 power supply, WSE control package, WC 100B circulator Pendant Control Serial # 25A947

M1011009 Custom 6’ x 4’ Torch Manipulator 6’ constant speed powered elevation from 25” to 97” from the floor to the bottom of the arm 48” variable speed reach 12” vertical slide for fine height adjustment 6” powered cross seam adjuster Manual rotary slide to level the reach arm Remote pendant station for all controls 230 or 460 volt

M131102 Aronson Locust-1 6’ x 4’ Manipulator  6’ constant speed power lift at 34 IPM from 19 1/2” to 91 ½” to the center of the boom 4’ variable speed power reach of 1.8 to 180 IPM from 13” to 61” from the center of the mast 400 lb. weight capacity 360° manual rotation on free standing X-base Pendant Control Shipping weight 2,000 lbs. Serial # 672

M141109 Pandjiris Model 172HD 6’x 6’ Hand Director  Constant speed power lift from 36” to 108” Manual mast rotation Manual reach from 43 ½” to 77 3/8” 5’x5’ X base 20’ pendant control 10” Setco powered slide Jetline CWF10A feeder Will hold weight of submerged arc system Serial #800-6699-10 Shipping dimensions: 8’Lx5’Wx9’H Shipping weight: 700 lbs.  

M121219 Aronson Locust-1 6’ x 6’ Manipulator 6’ constant speed powered lift from 29” to 101”Reconditioned Powered reach from 13” to 85” from the center of the mast rotation 400 lb. capacity at either or both ends Portable King Pin X-base 115 volt Shipping weight 2,000 lbs. Serial # 72107  

M121220 Aronson Locust-1 6’ x 6’ Manipulator Reconditioned 6’ constant speed powered lift from 29” to 101” Powered reach from 13” to 85” from the center of the mast rotation 400 lb. capacity at either or both ends Portable King Pin X-base 115 volt Shipping weight 2,000 lbs. Serial # 6718

M121223 Bartley 6’ x 6’ Manipulator 6’ constant speed acme screw driven lift from 32” to 104” Reconditioned Powered reach from 13” to 85” from the center of mast rotation 200 lb. capacity at either or both ends Fixed King Pin base 115 volt Shipping weight 2,000 lbs. Serial #N/A

M131025 Aronson Model 66 6’ x 6’ Manipulator 6’ constant speed powered lift from 25 1/2” to 97 1/2” Powered variable speed reach from 24” to 96” from the center of mast rotation 250 lb. capacity at either or both ends 5' x 5' base plate Jetline ALC 101 arc length control system and cold wire feed systems Miller weld oscillator package 460 volt Shipping weight 2,500 lbs. Serial # 6128177

M141110 Ransome 6’x9’ Ransome Manipulator 200 lb. weight capacity Constant speed Powered lift – 30” to 102” Manual mast rotation – 3.7 to 150 IPM Powered constant reach from 13” to 121” Variable speed 42”x72” base – can be converted into travel car for additional charge 230/460 volt – 3 phase Serial #615152 Shipping dimensions: 12’Lx72”Wx4’H Shipping weight: 3,500 lbs.

M904018 Ransome Model XXHD 7’ x 15’ Travel Car Manipulator As Is 7’ powered elevation from 77” to 164” to the bottom of the boom Reconditioned 2.7 to 108 IPM variable speed reach from 64” to 244” from the center of the mast rotation 360° power mast rotation 2,000 lb. load capacity either or both ends Mounted on a variable speed travel car that runs on 84” gauge rail track Track NOT Included 460 volt Serial #909286

M309004 Mark "V" 8' x 5' Manipulator and Travel Car 8' constant speed power elevation from 32" to 128" 5' variable speed power reach from 15" to 75" Manual mast rotation 6" Linde powered horizontal and vertical cross slides and a manual rotary slide All mounted on a manual travel car that runs on inverted angle iron track (track not included) Currently equipped with a l-Tec 650 cc/cv power supply GMA feed head and all cables Remote control console for all functions including welding process Serial #6620-34-31

M141001 Aronson Locust 8’x 8’ Welding Manipulator 300 lb. weight capacity on either or both ends Constant speed, powered lift from 30” to 126” Powered reach from 34’ to 110” at 3.3 to 100 IPM Manual mast rotation NA-5 submerged arc welding package Portable X-base 20’ pendant control 115 volt – 1 phase DC-600 Serial # u1960607124 Arco wand 7DMH flux recovery Shipping dimensions: 140”Lx6’Wx140”H Shipping weight: 3,000 lbs.

M141002 Aronson Locust 8’x 8’ Welding Manipulator 300 lb. weight capacity on either or both ends Constant speed, powered lift from 30” to 126” Powered reach from 34’ to 110” at 3.3 to 100 IPM Manual mast rotation NA-5 submerged arc welding package Portable X-base 20’ pendant control 115 volt – 1 phase DC-600 Serial # u1960607124 Arco wand 7DMH flux recovery Shipping dimensions: 140”Lx6’Wx140”H Shipping weight: 3,000 lbs.

M130701 7’ x 10’ Cecil Peck Manipulator PARTS ONLY AS-IS 7’ constant speed powered lift from 18” to 96” Powered reach from 43” to 120” from the center of mast rotation 300 lb. capacity at either or both ends 360° bolt down swivel base Cecil Peck 4 x 4 powered cross slides Lincoln NA-5 Submerged Arc system System includes: NA-5 head, control, flux hopper, coil adapter, cables and DC-600 power supply

M130604 Cecil Peck 8’ x 10’ Manipulator 8’ constant speed powered lift from 18” to 114” with welding equipment Powered reach from 43” to 163” from the center of mast rotation 500 lb. capacity at either or both ends 360° bolt down swivel base Lincoln NA-3 Submerged Arc system. System includes NA-3 head, control, flux hopper, coil adapter, cables and DC-600 power supply 460 volt Shipping weight 2,500 lbs. Serial #N/A

M140912P Aronson 8’ x 12’ Manipulator 300 LB. WEIGHT CAPACITY EITHER OR BOTH ENDS Constant Speed Powered lift from 29” to 125” Manual mast rotation 3.3 to 100 IPM Variable speed reach from 15 ½” to 159 ½” from center of boom X-frame base 2 Lincoln Powerfeed 10A 2 Pandjiris 615 slides Weld Engineering HAMX-50 flux hoppers 460 volt – 3 phase Serial # 9692 Shipping dimensions: 14’Lx8’Wx3’H Shipping weight: 3,000 lbs.

M404001 Precision 9’ x 9’ x 27-1/2’ Heavy Duty Manipulator/Travel Car System This system was manufactured for the robotics industry for precision welding on military vehicles Heavy duty mast has 9 ft. of constant speed of precision screw driven lift starting at approx. 36” from the floor to 144” high under the boom. The mast has manual rotation with lock Boom has 9 ft. of “dual pinion” variable speed gear drive and rolls on Thompson Roundway roller system Weight capacity approx. 750 lb. Travel car is 5’ x 5’ x 19” high and variable speed rack & pinion drive on 33 ft. of Thompson Roundway precision track All three 3-axis paths are accordion booted This system is now Servo driven We will change to Pendant AC-Inverter or D.C. drives

M120802P Ransome Model 99 9’ x 9’ Manipulator and Travel Car with Track 500 lb. capacity at either or both ends  with welding equipment 9’ constant speed lift from 42” to 126” 9’ variable speed reach from 18” to 126” from the center of the mast 1 to 62 IPM speed 360° manual mast rotation 5 to 200 IPM variable speed travel car that runs on 30’ of 33 gauge track Currently equipped with Lincoln NA-5 control and feed head 460 volt. Serial #N/A

M130202 Pandjiris C 10’ x 6’ Manipulator and Travel Car with Track 500 lb. capacity at either or both ends 10’ constant speed lift from 38” to 157” to the bottom of the boom when mounted on travel car 6’ variable speed reach from 54” to 126 ” from the center of the mast 1 to 62 IPM speed 360° manual king pin base on powered 56 1/2 gauge travel car 45’ of track 5 to 200 IPM 4’ x 7’ bolt on shelf to carry 2 welders Cable track for travel car 460 volt Serial # 25-3794

M140914 Pandjiris 10’ x 9’ Model 1400 Welding Manipulator  750 lb. weight capacity either or both ends 10’constant speed from 30” to 150” to the bottom of the boom No rotation Solid 40” round floor mount 3” to 116” IPM variable powered reach 54” to 162” from the center of the mast 6”x6” powered heavy duty slides Linde 2 roll feeders and controls Cable tray 460 volt, 3-phase Serial #800-7246-1 Shipping dimensions: 18’Lx8’Wx4’H Shipping weight: 8,000 lbs.

M130717 Pandjiris Series 1400 11’ x 14’ Travel Car Manipulator  w/travel car 11’constant speed powered lift from 42” to 174” Variable speed rack & pinion driven reach from 28” to 196” 360° manual mast rotation Mounted on a Model 30565 variable speed travel car that runs on 56 1/2” gauge track (track NOT included) Pandjiris 61P power slides 6” horizontal and vertical powered adjustment Lincoln NA-3N sub arc welding system Lincoln DC-1000 power supply and Invincible flux recovery unit 460 volt Serial # 800-6743-2

M140911 Ransome Model 1212 12’ x 12’ Manipulator 750 lb. weight capacity either or both ends 12’contant speed powered lift from 39 ½” to 183 ½” to the center of the boom 12’, 3.35 IPM to 134 IPM variable speed powered reach from 30 ½” to 174 ½” to the center of the boom 360° manual mast rotation on a bolt down base 20’ pendant control Currently equipped with a 10’ boom extension, Lincoln NA-3 and NA-4 controls and heads 460 volt – 3 phase Shipping dimensions: 20’Lx8’Wx5’H Shipping weight 9,000 lbs. Serial # 6219826

M140913 Ransome Model 1212 12’ x 16’ Manipulator  750 lb. weight capacity either or both ends 12’contant speed powered lift from 39 ½” to 183 ½” to the center of the boom 16’, 3.35 IPM to 134 IPM variable speed powered reach from 30 ½” to 222 ½” to the center of the boom 360° manual mast rotation on a bolt down base Currently equipped with a 6’ boom extension, Lincoln NA-3 and NA-4 controls and heads Pandjiris 6” powered vertical slide 460 volt – 3 phase Shipping dimensions: 22’Lx8’Wx5’H Shipping weight 9,000 lbs. Serial # 6219310  

M111103 Pandjiris 12’ x 12’ Model SWHM Travel Car Manipulator 12’constant speed powered lift from 48” to 192” w/travel car Variable speed rack & pinion driven reach from 24” to 168” 360° manual mast rotation Mounted on a variable speed travel car that runs on 56 1/2” gauge track (track NOT included) Lincoln NA-3 sub arc welding system and Arc Wand flux recovery unit 575 volt Serial # 25-1739

M131115P Aronson Locust-II 12’x 12’ Manipulator 300 lb. capacity at either or both ends 12’ variable speed lift from 37” to 181” 12’ variable speed reach from 15 1/2” to 195 1/2” from the center of the mast 1 to 62 IPM speed 360° manual mast rotation with pneumatic brake 360° welding head swivel Cable protection sleeve mounted on top of boom Pendant control for all functions 460 volt Serial # 9586

M131011 Aronson Scarab I 12' x 12' Manipulator 12' constant speed rack & pinion driven lift from 40.5" to 184.5" 12' variable speed rack and pinion driven reach from 18" to 162" 500lb load capacity either or both ends Manual mast rotation Mounted on a portable "X" frame base 480 volt 3 phase Serial #2984  

M100530P Webb MB1212 12’ x 12’ Travel Car Manipulator 12’ constant speed screw driven powered lift from 51” to 195” Variable speed rack & pinion driven reach from 32” to 176” 360° manual mast rotation Mounted on a variable speed travel car that runs on 56-1/2” gauge track (track NOT included) 230 or 460 volt Serial #7042

M150421 Ransome Model XHD 13' x 18' manipulator 1,500 lb. capacity either or both ends 3.4 to 136 IPM variable speed reach from 47" to 16' 11" from the center of the mast Constant speed lift from 37" to 21' 1"to the bottom of the boom 6' x 12' floor mount base plate 460 volt Shipping weight 22,000 lbs. Shipping dimensions: 26' long x 7' wide x 12' high Serial #639759

M131013 Aronson Scarab I 14' x 14' Manipulator 14' constant speed dual rack & pinion driven lift from 38.75" to 206.75" 14' variable speed rack and pinion driven reach from 18" to 186" 900 lb. load capacity either or both ends Manual mast rotation Mounted on a portable "X" frame base 480 volt - 3phase Serial # 81268

M710002 Ransome Model XXHD 13.5’ x 18’ Travel Car Manipulator 13.5’ powered elevation from 77-1/2” to 239-1/2”” to the bottom of the boom 2.7 to 108 IPM variable speed reach from 55” to 271” from the center of the mast rotation 360° power mast rotation 2,000 lb. load capacity either or both ends Mounted on a variable speed travel car that runs on 84” gauge rail track Track NOT Included 460 volt Serial #639089 Reconditioned to fit your needs

M120125 Ransome Model XHD 16’ x 16’ Manipulator 2008 Model 16’ constant speed power lift at 36 IPM from 53” to 242” to the center of the boom 16’ variable speed power reach of 1.8 to 180 IPM from 40” to 232” from the center of the mast 1500 lb. weight capacity either or both ends 360° Powered Rotation on Variable Speed travel car Travel car uses 84 ½ gauge train rail Rail not included Lincoln Tiny Twin arc welding system includes with Powerwave AC/DC 1,000 Dual wire drum holder Servo robot 6” vertical and horizontal powered slides and laser seam tracking system Arc Wand flux recovery system 575 volt Serial # 45238 Shipping weight 44,000 lbs.


USED WELD SEAMERS

S604011 “1990”Mills Machine 11” Longitudinal Plasma Seam Welder 11” overall welding / clamping length capacity 3-1/2” to 5-1/2” diameter capacity (can be increased with a riser) Variable speed screw driven carriage 3” pneumatic torch lifter Gas purge back-up bar Water cooled mandrel Dual water circulators Plasma welding equipment includes a thermal dynamics WC100B welding console Airco Heliwelder power supply and multi slope 2 sequence control Model 3A plasma torch and a Cyclomatic 80A magnetic welds oscillator Serial #N/A

S9801001A Custom GE Precision 12” Seam Welder 12” total clamping length capacity 16” total welding length 12” minimum part diameter and maximum diameter of 36” Foot controlled pneumatic clamping Variable speed precision carriage 1 1/2“manual horizontal torch adjustment and 3” manual vertical torch adjustment 115 volt Shipping weight 650 lb. Serial #11219

S502007 Jetline 12” Coil End Joining Seam Welder This seam welder’s primary use is to join together strips fed from coils The Jetline seamer clamping/welding bed is 12-1/2” long Has a variable speed carriage with #9026 control and two manual cross slides on the torch holder The one piece hold down clamps are air actuated with individual air valves There are 2 8” diameter primary strip guide rolls and 2 3” final guide rolls The welding package is a Miller 50A precision TIG welding power supply and air-cooled TIG Torch for the fusion only weld The whole system is mounted on a self-contained portable base Dimensions of the whole system are 78”L x 40”Wx 58”H Jetline Serial #84166

S121204 Jetline Model CS3-15Z 15” Coil End Joining Seam Welder 18” total welding/clamping length capacity This seamer was used to plasma weld steel coils together Precision screw driven carriage with Jetline 9627 control 2” vertical and 2” horizontal manual torch adjustment slides 4” vertical pneumatic torch lifter Continuous copper tipped aluminum fingers Gas purged back up bar Cable track Thermal Arc Ultima 150 Plasma welding system Accucutter 3001 manual bench shear Shear capacity is .015 steel and .040 aluminum Dual plate alignment fingers Alignment table to align sheet sides Table is horizontally adjustable depending on the sheet width Seamer and power supply roll on V-groove track with 7’ of travel 115/ 200-460 volt Serial # 080005.

S511005A Spaulding Model 24 Outside Corner Seam Welder This Machine was used to TIG weld the outside corners of aluminum, steel and stainless electric panel boxes 24” total vertical welding/clamping length capacity Arc Specialties main control Jetline 9029 control wire feeder Water cooled TIG torch 24” powered vertical torch travel 6” manual horizontal torch adjustment 12” vertical clamping adjustment Foot pedal controlled pneumatic clamping 115 volt Serial #N/A  

S412001 Cecil Peck “Dual Position” Outside Corner Seam Welder This machine was used to TIG weld the outside corners of aluminum, steel and stainless electric panel boxes The dual operator positions were used for weld lengths up to 17” long The air clamping device and copper mandrel plates could be increased (within reason) for longer welds The torch carriers are heavy duty variable speed devices that are ½ H.P. Dc motors & drives

S10302 Jetline LWS-24Z, High Production, Automatic Seam Welder This 1996 automatic plasma welding seam welder is a high production machine that features: automatic clamping & alignment for cylinders up to 24” long 18” to 25” in diameter .020 to .187 thickness Microprocessor control Thermal Arc Ultima 150 plasma welding system Safety palm buttons & guards Minimum operator skill required This machine was used for a short run product

S111003 Lee Shaffer SW24FA-P, High Production Seam Welder Features: automatic alignment for cylinders up to 24” long 5 1/2” to 40” in diameter .020 to .187 thickness Microprocessor control Thermal Arc Ultima 150 plasma welding system Safety palm button & guards Micro air fume extractor Designed for welding galvanized 460/110 volt Serial # 20013-d Shipping weight 2,750  

S120708P Pandjiris Model 36E 36” Seam Welder 42” welding/clamping length capacity 3 1/2” minimum part diameter 30” maximum part diameter Linde variable speed rack and pinion driven carriage with ESAB “J” governor carriage control Foot pedal control for pneumatic clamping 2” manual horizontal and vertical slides for torch adjustment Water cooled mandrel Gas purge back up bar Miller Syncrowave 300 welder 115 volt Serial #400-945

S100709 Airline/Jetline Model LW10306 36” Weld Seamer Rebuilt 42” total welding/clamping length capacity 3” minimum part diameter capacity 32” maximum part diameter capacity Variable speed Model OM-48 rack and pinion carriage that runs on an 8’ extended length side beam Gas purge back-up bar WPI touch screen weld control Edge alignment guides 

S612013 Pandjiris Model 36ES-30 36” Seam Welder 42” welding/clamping length capacity 3” minimum part diameter 30” maximum part diameter (can be increased with a riser) Variable speed rack and pinion driven carriage Water cooled mandrel 6” Manual cross slides WPI touch screen weld control Serial #400-8078

S140924 Airline 48” Longitudinal Seam Welder 48” total welding/clamping length capacity 3” wide continuous copper fingers Rack and pinion driven carriage WPI touch screen weld control 90° angle bracket with 6”x 6” cross slides Serial #N/A Shipping dimensions: 9’ x 5’ x 8’

S100906 Airline/Jetline 48” Longitudinal Seam Welder Rebuilt 48” total welding/clamping length capacity 3.5” minimum part diameter 32” maximum part diameter capacity (can be increased with a riser) Variable speed rack and pinion driven carriage WPI touch screen weld control New pneumatic system for finger hold down Serial #N/A

S130905P Weldlogic Model X-48 48” Seam Welder 48” maximum welding/ 51”clamping length capacity 4” minimum part diameter capacity 32” maximum part diameter capacity (can be increased with a riser) Variable speed rack and pinion carriage with Weld logic carriage control 6” Pneumatic torch lifter 3” manual vertical and 1” horizontal torch adjusters 4 roll cold wire feeder Weldlogic AWS-200N power supply RPW150-4CH pendant control and Dell laptop computer for programming Gas purged back up bar Pneumatic part clamping Cable track and tray to protect cables Pneumatic plate alignment bar Manual adjustment work piece stop block that attaches to mandrel 460 volt Pneumatic

S110804 SAF 48” Seam Welder54" total welding/clamping length capacity 8" minimum part diameter 42" maximum part diameter Rack and pinion driven variable speed carriage Retractable plate alignment arms Steel fingers w/aluminum tips Gas purge copper back-up bar Water cooled mandrel 2” Manual horizontal & 5” vertical torch adjustment 1-1/2” vertical wire adjustment Seamer currently equipped with SAF controls for TIG welding Cable rail on back of seamer to suspend cables above the floor 230 volt – 3 phase Serial #899

S608005 Hamilton Custom 48” Weld Seamer As is only 52” Welding/Clamping Length 9” minimum part diameter 58” maximum part diameter capacity Air clamping

S130301 Weldline Model J-955 60” Weld Seamer Rebuilt 66” total welding/clamping length capacity 3 1/2” minimum part diameter 30” maximum diameter Rack & pinion driven variable speed carriage with New WPI control Standard mandrel 2” manual vertical and horizontal slide with pancake swivel Continuous copper fingers Dual Jack screw powered part support at additional cost

S130302 Weldline Model J-955 60” Weld Seamer Rebuilt 66” total welding/clamping length capacity 3 1/2” minimum part diameter 30” maximum diameter Rack & pinion driven variable speed carriage with New WPI control Standard mandrel 2” manual vertical and horizontal slide with pancake swivel Continuous copper fingers Dual Jack screw powered part support at additional cost Welding equipment NOT included Serial #N/A Dual Jack screw part support

S512003 Webb Model J-68 5’ Seam Welder 68” total welding/clamping length 6” diameter minimum capacity 32” diameter maximum capacity .020 to .135 thickness capacity Water cooled mandrel Includes a Lincoln TC-3 variable speed travel carriage Lincoln NA-5 or NA-3 control and head Lincoln vertical and horizontal adjusters Lincoln DC-600 power supply 4” individual copper fingers Copper back-up bar Serial #59115

S140925 Pandjiris Model 72E6-36 72” External Seam Welder 78” total welding/clamping length capacity 6” minimum diameter capacity 36” maximum diameter capacity 3” individual fingers .1 to 60 IPM variable speed carriage square way/rack & pinion 4” pneumatic torch lifter 2” vertical x 2” horizontal rotary cross slides Plate alignment device Jetline Model 9627 carriage control (serial #010371) Jetline Model 9629 feeder control (serial #010306) CWF-10B feeder – 2 roll Pneumatic foot pedal activated clamping Wire speed .1 to 150 IPM Serial #800-2539-2 Shipping dimensions: 10’ x 4’ x 7’

S505001 Pandjiris Model 72-ES-52 72” Seamer with Welding Equip 78” total welding/clamping length 6” minimum part diameter 52” maximum part diameter 18” high riser that can be removed 3” individual fingers with replaceable copper tips 3” to 90” IPM variable speed carriage Equipped with a variable speed rack and pinion carriage Jetline Model 9027 carriage control Pneumatic torch lifter Water cooled mandrel Cable track and 4” powered vertical and horizontal cross slides New Miller S74DX feeder Reconditioned Miller 456P New American Weldquip 400 AMP air cooled MIG gun Serial #N/A Shipping dimensions: 10’L x 4”W x 8”H  

S110104P Ameco 72” Seam Welder As-Is with welding equip. 72” total welding/clamping length capacity bed only 10” minimum part diameter capacity 40” maximum part diameter capacity Linde OM-48 rack and pinion driven carriage Currently equipped with a Miller Deltaweld 451 automatic 1A and 4-roll wire feed head Serial #5640 

S611019P Pandjiris Model #572 72” Weld Seamer 78” welding/clamping length capacity 5” minimum part diameter 32” maximum part diameter (can be increased with a riser) Variable speed rack and pinion driven carriage Serial #25-1046

S140703P Jetline LWS-72Z, 72” Seam Welder 75” clamping length Seamer bed only 6” to 30” in diameter capacity Jetline 9026 carriage control Air cooled mandrel 2” manual horizontal slide 360° manual rotation slide 1” Jetline pneumatic torch lifter Foot pedal for part clamping Pendant control MIG or TIG capable Miller S-62 feeder 2 roll Miller HF-2510-1 Arch starter Miller SMT 304 cc/cv Miller Coolmate 4 115 volt Serial number 990215

S131113P Four Corp Model 100-72 72” Weld Seamer 72” Welding/clamping length capacity 7” Minimum part diameter 56” maximum part diameter (can be increased with a riser) Four Corp carriage control Four Corp variable speed rack and pinion driven carriage Miller a1d-4 welding system 4” manual horizontal and vertical slides 10' pneumatic cylinder lift Pneumatic mandrel latch 46” high walkway for easier cylinder adjustment 115 volt Serial # 85w1605

S131022 Airline LWS-72 72” Seamer/Side Beam 78” total welding/clamping length 6” minimum part diameter 56” maximum part diameter (currently has a 25” high riser that can be removed) Equipped with om-48 variable speed carriage J governor Digimatic 2 control and wire feeder 4 ½ inch manual horizontal and vertical adjustment slides 5” pancake swivel for torch angle adjustment Gas purged back up bar Cable hanger VI-450A power supply

S131024 Guild Model WS 150 72 72” Seamer/Coil Joiner/Planisher 72” Welding/clamping length capacity Hydraulic entry pinch rolls 6” x 88” 3/8” maximum weld capacity Hydraulic sheet hold down Acme screw driven linear bearing tray for torch movement Hydraulic full weld length planisher to smooth out and strengthen the weld. Maximum planishing .135” Hydraulic support tray for exiting piece Hobart cyber-TIG 300 DCS welder Job # cs-7881  

S131118P Webb Model J-80 80” Welding Seamer As-Is 80” clamping/welding length capacity 7” minimum part diameter capacity 40” maximum part diameter capacity with 13” riser Pneumatic powered clamping fingers Gas purged back up bar Water cooled mandrel Bug-O Mark 3 variable speed tractor and track 115 volt Serial # 6428

S912008 Webb Model J-80 80” Welding Seamer 80” clamping/welding length capacity 6” minimum part diameter capacity 32” maximum part diameter capacity Rack and pinion driven variable speed carriage Cable tray Water cooled back up bar 6” manual cross slides

S130503 Pandjiris Model 96-E8-36 96” Seam Welder As Is 96”total welding/102”clamping length capacity 8” minimum part diameter capacity 36” maximum part diameter capacity (diameter capacity can be increased with a riser) Jetline rack and pinion driven carriage and control with Esab “J’ Governor control Digimatic 2 weld control 4 roll wire feed head 4” vertical powered slide and 4” horizontal manual torch adjustment slides Water cooled mandrel Esab SVI 300i power supply Serial #400-1344

S140606 Jetline LWHP-96Z 8’ Powered Elevation Weld Seamer 102” total welding/clamping length capacity 7.25’ minimum part diameter 87” maximum part diameter (only 66.75” when using the existing drum cradle) Hydraulic powered elevation of the welding bed from the minimum height of 46” to a maximum of 92” 3” individual fingers 4” Pneumatic torch lifter 4” x 4” manual cross slide New WPI touch screen weld system control – compatible with any weld process Remote pendant controls for elevation, mandrel latching and finger clamping Jetline SWC-3B-9500 variable speed rack and pinion driven carriage Water cooled mandrel with pneumatic latch Gas purge back-up bar Includes electric hydraulic pump and a drum cradle that moves manually in and out on an inverted angle iron track for ease of loading up to 66” diameter tanks Cable tray & track for cable protection Welding equipment NOT included Serial #990494 Shipping dimensions: 12”L x 6”W x 9”H Shipping weight: 14,500 lbs.

S100711 Cecil Peck 8’ Weld Seamer 96” total welding/clamping length capacity 8” minimum part diameter capacity 42” maximum part diameter capacity (can be increased with a riser) Variable speed rack and pinion driven carriage Welding equipment NOT included Serial #N/A  

S121104 Pandjiris Model 96-E8-72 96” Seam Welder 96” total welding/clamping length capacity 8” minimum part diameter capacity 72” maximum part diameter capacity (can be increased with a riser) Pandjiris rack and pinion driven carriage and control Miller Auto 1DA-PS weld control 4 roll wire feed head 6” vertical and 3” horizontal manual torch adjustment slides Pancake swivel to adjust torch angle Copper tipped aluminum hold down fingers Copper flat plate gas purged back up bar Water cooled mandrel Cable track and tray Pandjiris sequence control Serial #600-4579

S910003P Pandjiris / Hobart 8’ Vertical Variable Polarity Seamer System includes an integrated Hobart VP-300S power supply As Is Gas control unit 8’ x 8’ manipulator and 8’ vertical seamer bed 4-roll wire feeder and all welding equipment

S130201 Amet / Jetline 8’ Vertical Variable Polarity Seamer System includes an Amet controller & operating console Amet Motor control center An integrated Miller Dynasty 700 power supply Custom gas control unit 8’ x 8’ manipulator and 8’ vertical seamer bed 4-roll wire feeder and all welding equipment Excellent for welding Aluminum Purchased New in 2002 for OVER $300,000.00  

S912009 Webb Model J-104 104” Welding Seamer 104” clamping/welding length capacity 8” minimum part diameter capacity 32” maximum part diameter capacity Rack and pinion driven variable speed carriage Cable tray Water cooled back up bar 6” manual cross slides

S140926 Airline 10’ Seam Welder 126” clamping length 32” in diameter capacity 3" individual fingers with copper tips Rack and pinion variable speed carriage Cable tray Two mandrel supports Riser can be added to increase diameter capacity Shipping dimensions: 15' x 5' x 8' Shipping weight: 12,000 lbs.

S140704P Jetline LWS-120 10’ Seam Welder 126” clamping length Seamer bed only 8” to 32” in diameter capacity Jetline 9026 carriage control Air cooled mandrel Jetline 9032 weld process control Two plate alignment devices 1” Jetline pneumatic torch lifter 2” manual horizontal slide for torch adjustment 360° manual rotation slide MIG or TIG as equipped Miller S-62 Feeder Miller HF-2510-1 Arc starter Miller XMT304 cc/cv Miller Optima control 115 volt Serial number 950326   

S807002 Jetline Model LWFS-120Z 10’ Flat Sheet Seamer 128” total welding/clamping length capacity 1” Air lift bed for ease of loading Includes a Jetline SWC-6A carriage with a 9026 control with a digital IPM meter 2” manual cross slides Gas purge back-up bar Welding equipment NOT included Serial #910315 

S130906P Cloos 10’ Flat Plate/Cylinder Seam Welder 120” total welding/clamping length capacity 20” minimum inside diameter 54” maximum outside diameter Cloos MIG welding package includes: GLC 503 Quinto power supply CK 78 DISD control Hydraulic tilting mandrel with powered rotation to change from flat plate to cylinders 2 Roller top hydraulic lift tables with pneumatic lifting arms (32” x 100” and 58” x 85”) 5' x 10' riser platform Foot pedal controlled pneumatic mandrel latch Pneumatic torch alignment/adjustment Swing out control arm Gas purge back-up bar Serial #N/A

S111104 O’Connor Model 138 11 1/2’ Internal / Flat Sheet Seamer 138” welding/clamping length .020 to 3/8” clamping range For flat sheet or I.D. welding on cylinders with a 24” minimum I.D. KAT Model GK-166 variable speed travel carriage and Model GRC-68 control Lincoln LN-4 Sub arc welding system w/ flux hopper 27” mandrel height Dual arm pneumatic clamping Serial #N/A

S140406P Binzel 20’ Flat Sheet/ Internal/External Weld Seamer 240” welding/clamping length 1/4 to 1 1/2” clamping range Flat sheet welding Internal welding 8' minimum diameter shell External welding 24” -32” diameter Binzel variable speed dual rack and pinion travel carriage 8” pneumatic vertical slide to raise torch 1 1/2” manual vertical and horizontal slides for torch fine adjustment 3/4” manual vertical and horizontal for wire guide fine adjustment Individual 4” wide aluminum fingers with replaceable copper tips Automatic pneumatic mandrel lock Dual manual worm gear finger adjusters Gas purged back up bar Replaceable 4' back up bar sections Automatic Pneumatic plate alignment bar 460 volt Serial #N/A

S121105P Pandjiris Model 240 FS 20’ Flat Sheet Seamer As Is 246” welding/clamping length 1/4 to 1 1/2” clamping range For flat sheet welding Lincoln model TC-3 variable speed travel carriage Lincoln NA-3 submerged arc welding system with 4” manual vertical slide Individual 6” Aluminum fingers Water cooled mandrel Height of mandrel is 24 1/2” 115V Serial # 651-3822  

 PLANISHERS

PL140927 Airline Model 41372CQ Combination Gantry Planisher 3” minimum diameter capacity 36” maximum diameter capacity 3 mandrels: 2 Ύ”, 6” and 10” 2 Ύ” mandrel rolls in on travel car Swing away arm to move larger mandrels out of the way Swivel planishing head to do both longitudinal and circumforential 2 extra sets of rollers, 1 flat, 1 dome 460 volt – 3 phase Serial #R1098 Shipping weight: 12’ L x 6’W x 8’H

PL140106P Geo Whiting Model 60 Longitudinal Weld Planisher For Planishing flat sheets or cylinders up to 60” Long .005 to .187” thickness capacity on aluminum or mild steel (1/8” maximum capacity on stainless steel) 13” to 36” cylinder diameter capacity Maximum planishing pressure 13,000 lbs. Serial #N/A

PL704001 Weldmation Model TU-1921 Vertical Planisher 1/8” thickness capacity 9” stroke capacity Ready for your custom designed tooling Serial #N/A  


SIDE BEAM CARRIAGE WELDERS

WS412001 Jetline Portable Heavy Duty Cast Long Length “Stellite” Overlay System Jetline tkk-24 precision screw drive (1-1/2” screw) side beam with 24” travel Heavy duty 9-1/2” power vertical slide 8” of z axis manual slide Long rod feeder with adjustable diameter guide Miller oscillator with center line steering Overall dimensions of portable side beam assembly - 76” high, 63” wide, 60” long System includes miller 300 AMP Synchrowave welder and TIG torch

SB507001 Linde 8’ Side Beam TIG Welding System 10’ side beam with a Linde om-48 rack and pinion drive variable speed carriage for a total travel length of 8’ Portable floor mounting stanchions for a fixed height of 59” to the bottom of the beam 4” manual cross slides and a rotary slide Cyclomatic avc-3 arc voltage control Miller weld oscillator Jetline cwf-10 cold wire feeder

SB504001P Jetline Model TKS-96 8’ “Powered Elevation” Side Beam 124” side beam with 8’ of travel length Jetline swc-3b variable speed travel carriage Powered elevation from 12” to 68” to the bottom of the beam Cyclomatic 4” x 4” mechanical seam tracker Serial #r4356

SB120817 Linde 10’ Side Beam Welding System 10’ side beam with a Linde om-48 rack & pinion drive variable speed carriage for a total travel length of 10’ Linde “J” governor carriage control Portable floor mounting stanchions for a fixed height of 53” to the bottom of the beam

SB120818 Linde 10’ Side Beam Welding System 10’ side beam with a Linde om-48 rack & pinion drive variable speed carriage for a total travel length of 10’ Linde “J” governor carriage control Portable floor mounting stanchions for a fixed height of 45” to the bottom of the beam

SB120819 Linde 10’ Side Beam Welding System Side Beam, Carriage and control only  Reconditioned w/stanchions 10’ side beam with a Linde om-48 rack & pinion drive variable speed carriage for a total travel length of 10’ Linde “J” governor carriage control

SB120820 Linde 10’ Side Beam Welding System Side Beam, Carriage and control only Reconditioned w/stanchions 10’ side beam with a Linde om-48 rack & pinion drive variable speed carriage for a total travel length of 10’ Linde “J” governor carriage control. 

SB609007 Jetline PST-300 Twin Head Overhead Bridge Side Beam 8’ of variable speed travel on both carriages mounted on the bridge 12’ variable speed travel on the side beam carriage 134” to the bottom of the side beam Welding torches are currently mounted on dual powered slides that have a total of 60” vertical travel Welding equipment includes 2 Airco pulse arc ii 550 cv power supplies Two Airco med-40 wire feeders Two Miller Coolmate 4 water circulators Two AWC 1,000 power assisted wire payoff reels Two Jetline 6” x 6” automatic seam trackers and a Jetline Jetstar programmable control

SB140308 Pandjiris Model PBT 12/192/21-12 16' Side Beam Welding System 12” to 6' diameter capacity 24” to 164” spacing between welding torches Three model 90 stanchions Two VSC-26-12 variable speed carriages controlled by individual pendants Each carriage has a Pandjiris 36” powered vertical slide and 6” manual horizontal slide mounted to a Pandjiris 180 ° swivel Cable track and partial trays to protect cables Three 18” x 18” x 1” steel pads for mounting to the floor. 115V Serial # 16600E00

SB131104 Reed/Webb Model U-8 Powered Elevation Side Beam  Reed 20’ side beam 2' to 8' work diameter Lincoln TC-3 variable speed travel car Powered elevation from 48” to 112” to the bottom of the beam Side beam is mounted to dual arms that swing back for part placement 230 or 460 volt Serial # N/A

SB804003 Jetline Model TKMV240 Dual Carriage Side Beam 240” Length Two Jetline model SWC-6DZ rack and pinion driven variable speed carriages Mounting stanchions and welding equipment NOT included Serial #969791

SB302001 Pandjiris GB PBT 12 20' Side Beam Welding System  Three model 60 stanchions VSC-21-12 variable speed carriage Miller automatic 1 head timers and 4-roll feed head Cyclomatic seam tracker Three axis manual cross slides Pulse arc control This is a factory integrated system with all equipment mounted and interfaced on carriage

SB812002 Bancroft 24’ Side Beam  22’ travel Rack & pinion driven variable speed carriage Mounting stanchions and welding equipment NOT included

SB502001 Jetline TK312 26’ TIG Welding Side Beam 28’ side beam with 26’ of travel 50” high floor mount stanchions and a Jetline model 9026 carriage control with a travel IPM meter Welding equipment to include the following: a Cyclomatic avc-3 arc voltage control A Jetline model 9029 cold wire feeder with a micro wire feed head A Cyclomatic 80A magnetic arc oscillator 5” manual horizontal slide and a 25” powered vertical slide Serial #920516

SB150423 Teledyne-Readco 33' Side Beam and Carriage 27' of travel on a heavy duty side beam Variable speed rack and pinion carriage Carriage capacity of 4,000 lbs. @ 12" from the face 3 ea. mounting stantions for a fixed height of 62" to the bottom of the beam Cable tray 460 volt Shipping dimensions: 33' long x 6' wide x 8' high Shipping weight: 14,000 lbs.

SB130207P Lincoln 55’ Side Beam Lincoln 55’ side beam Fixed height of 52” to the bottom of the beam Lincoln TC-3 variable speed travel carriage Two Lincoln NA-5 submerged arc welding systems System includes NA-5 control, welding head, flux hopper and wire reel Two cyclomatic seam tracker system with 5 x 5 slides Two invincible Model 4000 flux recovery units and two Lincoln DC-1000 welders Side beam and welding equipment only 460 volt Serial # N/A This unit would be excellent for welding I or H beams.

SB131020 Pandjiris Model PBT 12-840 Side Beam 70' Length Pandjiris model VSC 15-3 rack and pinion driven variable speed carriage M-VSC carriage control Miller S-64M feeder Cyclomatic seam tracker system System includes: Control panel, pendant control 10”x10” powered slides and interconnecting cables Cable track and tray for cable protection

SB131021 Pandjiris Model PBT 12-840 Side Beam 70' Length Pandjiris model VSC 15-3 rack and pinion driven variable speed carriage M-VSC carriage control Miller S-64M feeder Cyclomatic seam tracker system System includes: Control panel, pendant control, 10”x10” powered slides and interconnecting cables Cable track and tray for cable protection

 REBUILT WELDING LATHES

L606018 LSCA 26 dia. Custom 200 lb. Welding Lathe 24” round table with slots Ύ HP DC motor – 1725 RPM 200 lb. capacity 40” clamping length Minimum clamping diameter 1” Maximum clamping diameter 26” Manual tailstock with 2 locks 230/440 volt Serial #001 Shipping dimensions: 84”x48”x58”

L604009 Custom 12” GTAW Welding Lathe 6”-12” part length capacity 9” maximum diameter capacity 6” stroke pneumatic tailstock 5” pneumatic torch lifter All functions controlled by an Allen-Bradley SLC-500 programmable PLC Rotary ground Welding equipment includes a Powcon 150STP power supply and a 120 amp air cooled TIG torch Serial #N/A

L603010 Weldlogic Table Top 12” Lathe Variable Speed Fixed 6” table – ½” to 6” diameter through hole Weldlogic PA-100 power supply serial number 254 5” 3 jaw scroll chuck 3 ½” stroke pneumatic cylinder Live center on tailstock Manual adjustable slide for torch mounting 115 volt 1 phase Serial number 1308 Shipping dimensions 4’L x 3’W x 16”H Shipping weight 350 lbs.

L100413 Contour Arc Model FW Welding Lathe 26” length capacity 14.5” diameter capacity 200 lb. weight capacity Miller S-60 series wire feeder 115 volt Serial #141

L708011 Bancroft Model 605 Dual Head Welding Lathe 14” Maximum length capacity 14” Maximum diameter capacity 800 lb. load capacity Variable speed rotation from 1 to 20 RPM Weld overlap timer Two MIG welding heads that each include a Bancroft wire feed system 4” Vertical and 4” horizontal cross slides and air torch lifters 120 volt Serial #3559/115-990-1  

L809004 Compak-o-matic Model 1010 20” x 20” Mig Welding Lathe 20” maximum diameter capacity 20” maximum length capacity 7” pneumatic torch lifter 5.5” stroke pneumatic tailstock 3” vertical torch adjuster 2” horizontal torch adjuster 600 AMP rotary ground Wire feed head Welding power supply NOT included Serial #HG-113

L708009 Bancroft Model 1208 30 ° Incline Rotary Welder 800 lb. Weight capacity 44” maximum diameter capacity Welding bed is fixed at a 30 ° angle .01 to 10 RPM variable speed rotation Weld overlap timer Miller 60 series wire feed system with vertical and horizontal cross slides and an air torch lifter 120 volt Serial #3334/110-086

L608004 Jetline 14” x 14” MIG Welding Lathe 14” part diameter capacity 14” length capacity Jetline ZB-100 positioner 100 lb. weight capacity Air actuated tail stock for part clamping Vertical, horizontal and rotary cross slides Miller 300 amp power supply 230/460 volt Serial #910424

L130617 Bancroft Model 605 Welding Lathe 24” Maximum length capacity 14” Maximum diameter capacity 200 lb. load capacity Variable speed rotation from 1 to 20 RPM Weld overlap timer MIG welding head with Bancroft wire feed system 4” Vertical and 4” horizontal cross slides and air torch lifter 6” pneumatic part clamping from tailstock 360 ° torch swivel 180° pendant swivel Rotary ground 120 volt Serial #3502/114-372

L601001 Jetline Model CWP-24 90 ° Power Tilting Lathe Bed 200 lb. weight capacity
20.5” length capacity 12” diameter capacity For use as a vertical or horizontal welding lathe with a 90° powered tilting bed 8” capacity chuck with a 1/2” thru hole for back purging 3” air actuated tailstock for part clamping Jetline ALC101-V4T arc length controller Jetline Model 9024-101 circumferential TIG weld sequencer Variable speed torch carriage for Either Circumferential or Longitudinal Welding Powered torch lifter Powered slides 115 volt Serial #920131

L130204 Jetline Model CWP-24 90 ° Power Tilting Lathe Bed Refurbished Jetline Model CWP-24 Lathe
200 lb. weight capacity 24” length capacity 3-jaw chuck with ½” to 5 ½” diameter capacity For use as a vertical or horizontal welding lathe with a 90° powered tilting bed 3” air actuated tailstock for part clamping 10” manual head adjust slide 4” powered vertical torch adjustment 3” manual vertical slide Factory Refurbished Jetline 9500 Control A microprocessor based unit designed and built to provide low cost, accurate, repeatable control over the complete weld process. Designed to provide complete closed-loop control of four welding parameters during the weld process. Jetline CWF 10A Cold Wire Feed System Accurately feeds .020,.030,.045,1/16 and 3/32 hard and soft wires for mechanized TIG or Plasma welding Jetline ALC20T Arc Length Control Assures consistent, high quality welds on AC or DC applications by controlling the arc gap between the torch tip and work surface Moveable pedestal for controls Remotes all controls to a single moveable pedestal Refurbished Miller Dynasty 200DX Power Supply 150 amps of welding output at 60% duty cycle for AC/DC TIG welding The 200DX offers pulse on/off, pulse frequency, peak % time, background amperage, initial amperage, initial slope time, final slope time and final amperage control Refurbished Miller Coolmate 3 water circulator Weldcraft Water Cooled Machine Torch 115 volt Serial # 969257  

L120308 STS 24” Dual Head Welding Lathe 24” Maximum length capacity 36” Maximum diameter capacity Allen Bradley Panel View 600 Digital control Dual variable speed servo driven rotation from 1 to 220 RPM Two Miller Auto Axcess 300 power supplies Robotic wire feeders Tregaskiss MIG welding heads 7” Vertical and 10” horizontal pneumatic cross slides and air torch lifters Automated barrier curtain for safety 460 volt Serial # 2804-000

L906036 Quest 26” Dual Torch Welding Lathe 26” maximum part length capacity 18” maximum part diameter capacity 6” stroke pneumatic clamping Variable speed rotation 2 each manual adjustable torch mounts 2 each Miller 60 series feeders Power supplies NOT included 115 volt Serial #N/A 

L120309 Wolff Manufacturing Dual Head Welding Lathe 30” Maximum length capacity 32” maximum diameter capacity Variable speed servo driven rotation from 1 to 20 RPM 2 each sub arc welding heads that each include a wire feed system 19” vertical weld head adjustment Weld heads can be adjusted individually for angled work piece 10” horizontal chain driven oscillating cross slide Lathe can be rotated 45° to either left or right side Lathe controls powered off DC-600 power supply Two Lincoln DC-600 welders and Arc Wand flux recovery system with flux recovery tray under lathe 460/115 volt Serial # 283  

L906035 Quest 33” Dual Torch Welding Lathe 33” maximum part length capacity 20” maximum part diameter capacity 6” stroke pneumatic clamping Variable speed rotation 2 each manual adjustable torch mounts 2 each Miller 60 series feeders Power supplies NOT included 230 or 460 volt Serial #N/A

L408007 Edron Vertical Tig Welding Lathe 36" maximum length capacity 6" maximum diameter capacity Synchronized rotary drive of both top and bottom spindles Manual adjustable height on the top fixture Adjustable bottom fixture for irregular shapes Tig torch adjusts in and out by a cam following device 460 volt, 3-phase Serial #351870 Shipping weight - 3,500 lbs. Shipping dimensions - 5' long x 5' wide x 10' high

L408008 Edron Vertical Tig Welding Lathe 36" maximum length capacity 6" maximum diameter capacity Synchronized rotary drive of both top and bottom spindles Manual adjustable height on the top fixture Adjustable bottom fixture for irregular shapes Tig torch adjusts in and out by a cam following device 460 volt, 3-phase Serial #371628 Shipping weight - 3,500 lbs. Shipping dimensions - 5' long x 5' wide x 10' high  

L906033 Quest 36” Dual Torch Welding Lathe 36” maximum part length capacity 16” maximum part diameter capacity 6” stroke pneumatic clamping Variable speed rotation Two manual adjustable torch mounts Two Miller 60 series feeders Power supplies NOT included 230 volt Serial #N/A

L906034 Quest 46” Dual Torch Welding Lathe 46” maximum part length capacity 30” maximum part diameter capacity 6” stroke pneumatic clamping Variable speed rotation Two manual adjustable torch mounts Two Miller 60 series feeders Power supplies NOT included 115 volt Serial #N/A

L803015 Weldlogic Model CWT-102 Weld Lathe 200 lb. weight capacity 13” length capacity 12” maximum part diameter capacity 6” diameter 3-jaw self-centering chuck Arc length control Weldlogic Pulsarc 300-STD DC power supply Pendant Control Serial #523  

L804004 Merrick Engineering 64” GTAW Welding Lathe 12” maximum part diameter 64” Maximum part length 98” side beam with manual spotting car Merrick Volt Track II arc voltage control Cold wire feeder 2” manual cross slides 360° rotary slide Serial #N/A

L512002 Bancroft High Capacity 3 Station, Dual Torch, Indexing Welding Lathe 23” length capacity 12” diameter capacity 3 position indexing turret for loading of parts Welding of parts and cooling of parts Two torches for welding on both ends of parts GMAW welding equipment includes 2 Miller S-62 wire feeders with Tweco water cooled auto guns on 4” Bancroft retractable air slides Serial #3327/109-843

L100409 Bancroft VHI-18 Vertical Lathe 30” length capacity between the headstock and the tailstock (currently equipped with an air clamping fixture that limits the length to 11” 8” diameter capacity with the current torch mount (the mount could be altered to accommodate a diameter of 35”) 400 lb. weight capacity A synchronized rotary drive rotates the opposing vertical spindles at the same speed This maintains the radial alignment between two parts with no chance of slippage Welding equipment NOT included 230 or 460 volt Serial #3899/124-001 

L100410 Bancroft VH-18 Vertical Lathe 30” length capacity between the headstock and the tailstock (currently equipped with an air clamping fixture that limits the length to 11” 8” diameter capacity with the current torch mount (the mount could be altered to accommodate a diameter of 35”) 400 lb. weight capacity A synchronized rotary drive rotates the opposing vertical spindles at the same speed This maintains the radial alignment between two parts with no chance of slippage Welding equipment NOT included 230 or 460 volt Serial #3820/121-347

L100411 Bancroft VHI-18 Vertical Lathe 30” length capacity between the headstock and the tailstock (currently equipped with an air clamping fixture that limits the length to 11” 8” diameter capacity with the current torch mount (the mount could be altered to accommodate a diameter of 35”) 400 lb. weight capacity A synchronized rotary drive rotates the opposing vertical spindles at the same speed This maintains the radial alignment between two parts with no chance of slippage Welding equipment NOT included 230 or 460 volt Serial #3826/122-103

L100412 Bancroft VH-18 Vertical Lathe 30” length capacity between the headstock and the tailstock (currently equipped with an air clamping fixture that limits the length to 11” 8” diameter capacity with the current torch mount (the mount could be altered to accommodate a diameter of 35”) 400 lb. weight capacity A synchronized rotary drive rotates the opposing vertical spindles at the same speed This maintains the radial alignment between two parts with no chance of slippage Welding equipment NOT included 230 or 460 volt Serial #3572/116-145 

L305001 Bancroft Model VH-24 Welding Lathe 33" Long x 48" diameter capacity Pneumatic torch lifter Forward and reverse variable speed Weld overlap timer and a Miller 60m control and feed head Serial #3609-(117-212)

L305002 Bancroft Model VH-24 Welding Lathe 33" Long x 48" diameter capacity Pneumatic torch lifter Forward and reverse variable speed Weld overlap timer and a Miller 60m control and feed head Serial #3610-(117-213)

L206001P Stoody Screw Flight Tig Hard Surfacing Lathe Capacity of 7" Diameter (may be increased) x 144" Long This Machine was used for Hard Surfacing with #6 CoCrA solid lengths Oscillating Head Preheat System Control Console and 500 amp Miller DC Power Supply  

L9912001 Bancroft Welding Lathe As Is Work piece capacity 24” x 72” Reconditioned Bed 12’ overall Tailstock has air cylinder for part clamping Linde automatic head w/cross slides Variable speed rotation forward and reverse  

L610002 Jetline Model CWL-72 Lathe and 13’ Side Beam 500 lb. capacity variable speed headstock / tailstock 30” diameter capacity 72” length capacity (can increased to 48” - 120” capacity with a spacer) 13’ side beam with a manual spotting car that has 12’6” of travel Jetline model 9500 system control ALC-201v6e arc length control Rotary slide and horizontal slide Serial #81322

L131110P Pandjiris 72" Beta Dual Torch Welding Lathe 2,500 at 5" center of gravity weight capacity 22" to 72" length capacity 2" to 18" diameter capacity Each end has a Cyclomatic 10" x 10" seam tracker Tailstock moves along the base by a rack and pinion manual hand wheel Air actuated parts lifter with manual adjustments for ease of loading Pandjiris EZ Link system control This lathe was designed to weld end caps on small tanks Welding equipment NOT included 115 volt Serial #14564E00

L1054413 Melton Model 6330 Single Torch Welding Lathe Capacity 30” dia. X 37” long Programmable A.B. SLC 500 control Pneumatic fixture clamping Miller Maxtron 450 pulse welding system with automatic 1da control & head Welding system completely integrated Safety light curtain Operator console w/palm buttons Automatic leather curtains Hood for exhaust Complete, ready for your fixturing Serial # 6330 “1993”

L502001 Centurion Model WL24X168 Welding Lathe 24” diameter capacity 168” length capacity Variable speed travel car and a manual spotting car Pandjiris model “A” 31-1/4” capacity “gripper” chuck Manual tailstock mounted on a powered travel car Powered elevation side beam Includes a Lincoln DC-600 power supply with a NA-3N sub-arc system

L130206P Jetline Model CWB 5-240 Lathe Bed 1,000 lb. weight capacity. 500 lb. clamping pressure
5”-240” length capacity 15” maximum diameter capacity 6” air actuated tailstock for part clamping Jetline model 9500 controller Jetline ALC-201 arc length controller with powered torch lifter Variable speed carriage 5” horizontal and vertical manual slides mounted to 7” diameter pancake swivel Miller PC-300 GTAW pulse control Weldcraft TIG torch 500 Amp ground 115V/Air Serial # 960023  

L110203 L.A.G. Industries Dual Sided Welding Lathe 24’ Lincoln side beam with 2 each Lincoln TC-3 variable speed travel carriage 80” height of the bottom of the beam A dual sided variable speed headstock that sits on a manual travel car on 26.5’ of track Two live center idlers mounted on manual travel cars All travel cars lock into place every 2.75” Maximum combined length capacity of 16.5’ 43” height to the center of the rotational axis off the floor Lathe has a swing capacity of 52” System includes 2 Lincoln DC-1000 Power supplies with NA-5 controls and heads Previously used to overlay 2 steel mill rolls at a time Serial #N/A

L110204 L.A.G. Industries Dual Sided Welding Lathe 22’ Lincoln side beam with 2 Lincoln TC-3 variable speed travel carriage 80” height of the bottom of the beam Dual sided variable speed headstock that sits on a manual travel car on 26.5’ of track Two live center idlers mounted on manual travel cars All travel cars lock into place every 2.75” Maximum combined length capacity of 16.5’ 43” height to the center of the rotational axis off the floor Lathe has a swing capacity of 52”


CIRCUMFERENTIAL GIRTH WELDERS

C110106P Custom Weld-a-Round 40” square work table 4” to 24” diameter capacity 300° variable speed torch rotation 5” air powered part clamping 230 volt

C608003 Compakomatic Model 1025 Rotomatic MIG Weld-A-Round  0 to 6” diameter capacity Manual adjustable height Variable speed from .30 to 15 RPM Adjustable rotational overlap from 0 to 360° 6” air torch lifter Model 375 rotational control 600 amp current capacity Miller 300 amp power supply Serial #gm-154

C804006 Compakomatic Model 920E Weld-a-Round 8” maximum part diameter 13” maximum part height (can be increased with a riser) 7” pneumatic torch lifter Compakomatic series 400 control 115 volt Serial #GM241

C604008 Machine Technologies GTAW Weld-a-Round 12” part diameter capacity 6” part height capacity (can be increased with a torch riser) 1” vertical torch lifter Weld overlap timer All functions controlled with a programmable PLC Welding equipment includes a 1994 Miller Maxstar 152 with snap start Miller water circulator 250 AMP water cooled TIG torch Serial #1-549-2  

C508001 Rumble Automation Weld-A-Round Circular “Spud” Welding Station 5” vertical stroke Variable speed torch rotation by a 3 turn potentiometer 36” high work table 32” part diameter capacity 6” diameter weld capacity Currently equipped with a Hobart auto-CVS wire feeder

C140930P Bancroft 300 Circle Welder 1” to 14” diameter capacity 5” to 17” height capacity in 6” increments Rise and fall cam 4” pneumatic torch lifter Cold wire feeder No table 115 volt Serial #8662-02 Shipping dimensions: 5’Lx4’Wx6.5’H Shipping weight: 750 lbs.

C110312 Bancroft Weld-A-Round 300 Circular “Spud” Welder  The Weld-A-Round 300 is the most popular stationary circular welding system in the welding industry 300 AMP ground capacity 75 lb. clamping force 8” vertical stroke 0.7 to 14 RPM travel speed Bench mounted Welding equipment not included Shipping weight 700 lbs. Serial #4269/131-212

C110314 Bancroft Weld-A-Round 300 Circular “Spud” Welder The weld-a-round 300 is the most popular stationary circular welding system in the welding industry 300 AMP ground capacity 75 lb. clamping force 8” vertical stroke 0.7 to 14 RPM travel speed Bench mounted

C612014 Bancroft Weld-A-Round 300 Circular “Spud” Welder  The weld-a-round 300 is the most popular stationary circular welding system in the welding industry 300 AMP ground capacity 75 lb. clamping force 8” vertical stroke 0.7 to 14 RPM travel speed Equipped with rise and fall option  

C609008 Bancroft Weld-A-Round 300 Circular “Spud” Welder 75 lb. clamping force 300 AMP ground capacity 8” vertical stroke 0.7 to 14 RPM travel speed Bench mounted · Welding equipment not included Shipping weight 1,100 lbs. Serial #N/A

C906001 Bancroft Weld-A-Round 300 Circular “Spud” Welder  The Weld-A-Round 300 is the most popular stationary circular welding system in the welding industry 300 Amp ground capacity 75 lb. clamping force 8” vertical stroke 0.7 to 14 RPM travel speed 24” diameter round table · Welding equipment NOT included Shipping weight 950 lbs. Serial #N/A

C512001 Bancroft 350 High Capacity Dual Head, 3 Station Indexing Weld-a-Round  Bancroft is the manufacturer of the most popular stationary circular welding system in the welding industry Both weld stations have 8” vertical stroke with a 150 lb. clamping force and variable speed torch rotation from 0.7 to14 RPM 300 amp capacity A 3 position indexing table for loading of parts and welding under 2 separate weld stations Can be used for 2 passes on one part or one pass on two individual parts with proper fixtures Currently set up for GTAW application Serial #3300/109-003  

C141108 Bancroft 500 Circle Welder 500 AMP Variable speed 1” to 6” diameter capacity .5 to 6” IPM Square table – 12”x22” no slots Height 30” to 36” in 6” increments Thermal arc welding system: Powermaster 500P (Serial #M3062001006) 4 roll feeder HMC-410 control 8” pneumatic torch lifter 2.5” vertical manual adjuster 6” horizontal manual adjuster Pneumatic safety curtain Electronic safety curtain Forklift pockets for easy relocation 115 volt plus air (230 or 460 for welder) 3 phase Serial #4109/127-900 Shipping dimensions: 5’Lx4’Wx6.5’H Shipping weight: 750 lbs.  

C130111 Bancroft Weld-A-Round 500 Circular “Spud” Welder The weld-a-round 500 is the most popular stationary circular welding system in the welding industry 500 AMP ground capacity 150 lb. clamping force 30” round slotted table Adjustable table height from 27” to 36” 8” vertical stroke 6” manual horizontal and 2” vertical torch adjustment 0.7 to 14 RPM travel speed · Welding equipment not included 115 volts/air Shipping weight 950 lbs. Serial #3473/113-883-4  

C130112 Bancroft Weld-A-Round 500 Circular “Spud” WelderThe weld-a-round 500 is the most popular stationary circular welding system in the welding industry 500 AMP ground capacity 150 lb. clamping force 30” round slotted table Adjustable table height from 27” to 36” 8” vertical stroke 6” manual horizontal and 2” vertical torch adjustment 0.7 to 14 RPM travel speed · Welding equipment not included 115 volts/air Shipping weight 950 lbs. Serial #3473/113-883-5

C130205 Bancroft Weld-A-Round 500 Circular “Spud” Welder The weld-a-round 500 is the most popular stationary circular welding system in the welding industry · New in 2010 Water cooled torch with wire feed system 500 AMP ground capacity 150 lb. clamping force 41” x 90” horseshoe roller top table 8” vertical stroke 6” manual horizontal and 2” vertical torch adjustment 0.7 to 14 RPM travel speed Digital display Laser pointer for locating welding head on the part Allen Bradley c-600 touch screen control Operator control pedestal · Power supply not included 115 volts/air Shipping weight 1,100 lbs. Serial #4464/136-506

C501001 WeldLogic CWT-12-15V Vertical Welding Positioner Precision vertical positioner with self-centering 3 Jaw chuck 6” diameter torch holder post with pneumatic torch retract 100 lb. capacity Serial #CWT-12SN9413  

C412001 Alloy Custom Circular Welder 75 lb. capacity Variable speed (0.8 – 50 RPM) 4” 3-jaw chuck lever actuated gravity type part hold down mounted on 6” slide 6” maximum part diameter 6” maximum part height 3 axes of torch adjustment Analogue weld control – 10 turn potentiometer for accurate speed control start/stop w/ e-stop forward/reverse Manual flip-down 4” x 5” shaded lens for weld viewing

C205002 Alltra Corporation Model VWL2436 Circular Welder Vertical lathe with an 18" part diameter capacity 24" part length capacity and an air actuated centering head A complete system that includes a Lincoln dc-400 cc/cv power supply Lincoln na-5r head and control with a Lincoln analog interface procedure control Miller Coolmate 4 water circulator 20" motorized horizontal and vertical cross slides Allen-Bradley slc5/04 control and Allen-Bradley panel view 1400 monitor with operator friendly touch screen programming · Manufactured in 1998 Serial #2211

C912010 Cecil Peck Circular Welder Manual table lift No table 1" to 6" diameter capacity Variable speed rotation Pedestal control console for all functions · No welding equipment Serial #N/A

C805022 Cecil Peck Circular Welder Hand Wheel Table Lift 1 to 6” welding diameter capacity 43” part diameter capacity Variable Speed Rotation Pedestal Control Console for all Functions · Welding equipment NOT included Serial #N/A  

C406001P Cecil Peck Circular Welder Manual table lift No table 1" to 6" diameter capacity Variable speed rotation Pedestal control console for all functions · No welding equipment Serial #N/A

C204001 Cecil Peck Circular Welder
Hand wheel table lift 36" x 30" tee slotted table Variable speed rotation Pedestal control console for all functions Equipped with a Lincoln na-2 submerged arc control and welding head and a r3s-600 power supply Serial #69203

C140916 Cypress Model CW-11 Circle Welder 10” to 50” diameter capacity .2 to 2.2 variable speed IPM 7” cam slide manual adjustment 18” horizontal manual adjustment slide 2 roll feed head Lincoln LN-8F squirt welder (SN# 41971103979) Code 9962 115 volt Serial #B981224 Shipping dimensions: 4’Lx4’Wx5 ½’H Shipping weight 490 lbs.

C140917 Cypress Model CW-11 Circle Welder 10” to 50” diameter capacity .2 to 2.2 variable speed IPM 7” cam slide manual adjustment 20” horizontal manual adjustment slide 20” vertical manual adjustment slide 3 leg base Sub arc reel arm Lincoln LN-8F squirt welder (SN# 41971103980) Code 9962 115 volt Serial #B981223 Shipping dimensions: 4’Lx4’Wx5 ½’H Shipping weight 490 lbs.

C906038 Quest Large Capacity Weld-A-Round 14” maximum part height capacity 1” to 46” part diameter capacity 6” pneumatic stroke clamping Digital speed tachometer Currently equipped with a Miller Deltaweld 452 power supply and a S-64 series feeder 230 or 460 volt Serial #N/A

WS006003 Hobart/Aronson 2 Station Automatic Spud Welder MIG welds rings up to 12” diameter Two alternate weld stations w/air clamping of parts Control console w/ station selection Many tooling fixtures Variable speed rotation By 2 Aronson positioners Includes Hobart dual wire feeder, torches and welder  


 USED AUTOMATIC WELDING SYSTEMS

WS993001A Magnafloat Model 10 Welding System 10 lb. load capacity 1/2” to 12” diameter capacity Magnetic part rotation 24” x 30” flat table 1.5” to 19” height adjustment Self-adjusting weld alignment Serial #1200-0001 Shipping dimensions: 40”Lx24”Wx72”H Shipping weight: 200 lbs.

WS100613 Bug-O Model # UNI-BUGIII Welding System Stitch welder and cutting system Variable speed 4 to 75 IPM Will run on a 6” radius and larger Produces stitch and continuous welds Programmable by distance Used for cutting straight and custom shapes Includes NEW single gun welding kit (Bug-1855) Serial #0320205 Shipping dimensions: 12”Lx12”Wx12”H Shipping weight: 35 lbs.

WS141111 Ogden Dart Welding System 1” to -15” height .1 to 25 IPM Lincoln TC-3 variable speed carriage 117” of weld travel Dual adjustable sub-arc head 1” to 3” weld width adjustments Single flux recovery system with tornado 8900 vacuum 16” manual vertical slide Portable frame – used for dual fillet welds 115 volt Serial #1275 Shipping dimensions: 15’Lx8’Wx8’H Shipping weight: 2,000 lbs.  

WS140928 Hobart/Pandjiris “1987 Model” Dabber Welding System Constant Servo precision powered lift from 38” to 96” Manual reach from 32” to 48” Positioner has 30” table - 1,500 lb. capacity Positioner has 42” of manual travel on roller bearing roundways Manual latch to lock in place 6” pancake rotary slide 6” cyclamate powered torch lifter 4 roll Hobart feeder 45° manual torch adjuster 6” manual horizontal adjustment slide 8” powered vertical adjustment slide

WS131018 Bug-O Model MPD-1000/WPD-2100 Bug-O Programmable drive and pendulum weaver system 8 foot track section available Pendant for all controls  Magnetic track mounts available Uses standard 96” sections of track Carriage options include: Idler carriage, rack arm, rack box, forward & reverse limit switches and gun/torch holder 2-120 IPM speed range 12” of reach from center of carriage 115 volt

WS100546P Pandjiris 4 Head Gantry Welding System Heavy duty gantry mounted on twin powered travel cars that runs on twin 60 lb. track with 59” between rails 166” side beam with 60” powered vertical lift (currently configured for 36”) Two powered travel carriages, each with 2 Lincoln NA-5 Heads and 2 Cyclomatic mechanical seam trackers Four Lincoln DC-1000 power supplies Invincible flux recovery system

WS100305P Ogden “Dart” Dual Head Submerged Arc Beam Welding System 117’ welding table that has 50’ of hydraulic clamping by cylinders every 12” down the 50’ length 5” to 26” clamping capacity Two hydraulic pumps with reservoirs Variable speed welding carriage with 15” air powered vertical lifters 30” horizontal air powered slides and manual spring loaded seam trackers 2 Lincoln DC-1500 power supplies 2 Lincoln NA-5 controls and heads that each are set up for tiny twin arc wire Flux recovery system and all cables with cable tray Serial #1570  

WS901021 Pandjiris Stationary Manipulator Arm and Unit Frame Turning Roll System A Pandjiris stationary manipulator arm with a fixed height of 45.5” under the arm and a length capacity of 40’ The turning rolls have a 68,000 lb. turning capacity 7’ to 14’ diameter capacity with a fixed axel center of 72” Variable speed rotation 5 sets of 5” wide x 20” diameter rubber wheels spaced over the 30’ length of a variable speed travel car that runs on 69” gauge rail track Welding equipment can be mounted on the end of the manipulator arm for internal longitudinal or circumferential welding on cylinders 460 Volt Serial #66-4595

WS901022 Pandjiris Stationary Manipulator Arm and Unit Frame Turning Roll System A Pandjiris stationary manipulator arm with a fixed height of 45.5” under the arm and a length capacity of 40’ The turning rolls have a 68,000 lb. turning capacity 7’ to 14’ diameter capacity with a fixed axel center of 72” Variable speed rotation 5 sets of 5” wide x 20” diameter rubber wheels spaced over the 30’ length of a variable speed travel car that runs on 69” gauge rail track Welding equipment can be mounted on the end of the manipulator arm for internal longitudinal or circumferential welding on cylinders 460 volt Serial #N/A  

WS809001 Compak-o-matic Model 440A 6” Linear Dual Torch MIG Welding System  6” maximum welding length Dual torch with up to 13” between the torch heads 6” manual in/out slide for fine adjustment 3” manual right/left fine adjuster 6” stroke in/out indexing table for loading and unloading System includes 2 wire feeders and system controller Welding power supplies NOT included Serial #GY211 

WS704015 Hobart Manipulator/Positioner TIG Welding System Includes a 1,500 lb. capacity at 4” center of gravity positioner with power tilt and variable speed rotation Positioner is mounted on a manual travel car with 2’ travel Manipulator has powered lift from 30” to 90” Manual reach from 35” to 59” from the center of the mast 6” horizontal adjuster Jetline model ALC- 401-6 Arc Length control and model 9629 controller Jetline CWF-10A cold wire feeder All equipment mounted into a single skid frame base Serial #41-1641

WS703010 Cissel 12’ x 4’ Submerged Arc Welding Gantry 12’ variable speed rack and pinion driven carriage 4’ variable speed Lincoln TC-3 carriage on the cross boom Complete Lincoln NA-5 sub arc package Serial #111978

WS702002 Weldlogic Positioner/Tig Welding System Weldlogic 200 lb. capacity positioner with a 12” capacity chuck integrated with a Weldlogic complete GTAW welding system Welding system includes a Weldlogic RPW-2000 power supply Weldlogic cold wire feeder Weldlogic arc length control Weldlogic weld oscillator and pendant control for programming all functions 230 volt Serial #9914760

WS604010 “1996” Weldline / Miller GTAW Circular Welding Station  Weldline automation model wa-2 200 lb. capacity positioner with a ½” to 16” capacity 3-jaw chuck Weldline 6” arc length control Weldline weld sequence control Weldline cold wire feeder 4” manual cross slide and rotary slide Pneumatic part clamping Welding equipment includes a Miller XMT-304 inverter power supply Miller hf-251d-1 high frequency arc starter Miller pc-300 pulse control Tweco TC900 water circulator Weldcraft WP-27 500 amp water cooled TIG torch Serial # N/A

WS601002 Arc Systems Automatic Pipe Welding SystemSystem includes a Preston-Eastin hs-2s 2,000 lb. Capacity at 6” center of gravity Headstock with a 20” diameter scroll chuck that has a 6-1/2” thru hole Weldlogic aws-150 advanced TIG welding system that includes controls for variable speed rotation of headstock Weld current control Arc distance control Cold wire speed control and feeder and a 1.0 to 150 amp DC power supply Three 6” manual slides for 3 axis adjustment of torches All controls are mounted in a single remote pendant control 230/460 volt Serial #hs2s-13

WS509001 Pandjiris “1998” Hot Wire TIG Pipe Welding Station Complete hot wire TIG pipe welding station that includes a Pandjiris 4’ x 4’ manipulator on travel car Two Pandjiris HS-20PE-VS headstocks with TJ-20 chucks Pandjiris pipe supports on manual travel cars Miller/Jetline welding package and a complete set of 50’ tracks

WS507001 Mark Five Manipulator/Turntable System Turntable: 1,000 lb. capacity 20” high 24” diameter table with slots Variable speed drive from .01 to 1.4 RPM The manipulator is fixed over the turntable with a manual lift of 34” from 5.25” to 39.25” above the table and a manual reach of 24” Serial #JN-1189

WS140105 Ransome/ Jetline 2,000 lb. Weld System 2,000 lb. capacity at 6” center of gravity Variable speed rotation 24” round slotted table 30 ° tilt Jetline ALC-201 Arc length control and CWF10A wire feed systems Manual adjustment radial arm with 6” vertical movement and 16” horizontal movement to position welding torch Pendant control for all functions 230 volt 3 phase Serial #N/A

WS611017 MIM Industries Laser Welding System Allen Bradley panel view 550 control 1” pneumatic vertical part clamp 1” pneumatic horizontal and vertical laser adjustment slides Full steel enclosure Pneumatic powered front guard door Dual safety switches for process start · Laser not included 230 volt 1 phase Serial #N/A

WS404001 Ransome Positioner / Manipulator / Sub-Arc Welding System System includes a Ransome 5p 500 lb. capacity at 6" center of gravity Positioner (serial #1314851) Power tilt Variable speed rotation and manual height adjustment 3jc40 40" diameter 3-jaw, self-centering welding chuck Ransome model 99 manipulator (serial #9526562) with 72" power elevation from 0 to 71" at the torch Fixed boom with a manual spotting car from 44" to 88" from center of the mast Manual mast rotation Complete Lincoln DC-600 sub-arc system with NA-5 control weldhead Invincible flux recovery system  

WS406001 Pandjiris Model SWPT-102 Dual Side Beam Stiffener Welder HD welding carriage Variable speed (0 – 200 IPM) Twin cyclomatic seam tracking systems to locate torches on opposing sides of stiffener Open-end gantry style yoke with 96" of weld length allows loading of stiffener from one end Advancement of sheet is readily done with help from pneumatic plate lift rollers that automatically lift part off back-up bar between welds 15 pneumatic hold down clamps and part locators designed to automatically locate and hold "I" or "U" shape stiffener in place on sheet No tooling or jigs necessary for part alignment Back-up bar for heat sink and part distortion control System is capable of feeding aluminum or steel wire using GMAW process Twin 180◦ water-cooled GMAW torches for high production Remote Control Podium Was used for welding stiffeners for aluminum dump truck beds and bodies Very unique piece of equipment

WS408001 Compak-o-Matic Rotary Welding Station System includes a Ransome B-100 100 lb. capacity welding positioner Compak-O-Matic PC-300, 300 amp CV power supply Model 320 wire feed system with a machine torch 8” horizontal and vertical torch adjusters Model 263 control module with weld time function Serial #1530

WS999001 Linde/Jetline HWC-7 Cold Wire TIG System Jetline ZB-100 positioner on moveable screw drive base Complete with HW-500SS welder Auto controls Cross slides Floor standing base

WS140705 Pandjiris Butterbead Overlay System Fixed height at 92” from the bottom of boom to the floor Variable speed reach from 24” to 96” from the center of the boom 300 lb. capacity at either or both ends of boom Variable speed travel car that runs on 56 ½ 30 lb. rail track 40’ of track included with system Cable track and tray for cable organization and protection Lincoln NS-5 submerged arc welding system Lincoln DC-1500 power supply Cyclomatic seam tracker system with 10” x 10” powered slides Jetline 9200 Oscillator system with 0 to 4” maximum stroke width Pandjiris 24” vertical powered slide Donaldson/Torit mini trunk flume extraction system Dual Weldmatic D10 wire de-reelers with power feed and wire straighteners Serial numbers: System 11563E00, Drawing number 521826D 1-3, Lincoln DC-1500 41970913602,
NA-5 41970911926
 

WS605013P Cybotech Automatic Manipulator/Positioner TIG Welding System System includes a Fabspec 2,500 lb. capacity positioner 6 axis Cybotech 4’ x 3’ manipulator/6’ travel car Cybotech RC-6 controller Cold wire feeder Miller Syncrowave 300 w/SP-4 Pulser System offers 9 axis of powered movement

WS605014P Cybotech Automatic Manipulator / Positioner TIG Welding System System includes a Fabspec model 1840 2,000 lb. positioner 6 axis Cybotech 4’ x 3’ manipulator/6’ travel car Cybotech RC-6 controller Cold wire feeder Cybotech EPU power supply System offers 9 axis of powered movement


 ROBOTIC POSITIONERS

RP100726 Hobart Model MT1-500-S2B 500 lb. “Skyhook” Style Positioner 500 lb. capacity at 6” center of gravity Work table is off set 19” from the center of the rotational axis on the headstock 32” from the center of the table to the headstock face plate Currently equipped with servo motors Serial #2153  

RP703001P Fab Spec Model GDI-500 Robotic Positioner Two station articulating positioner, for load & weld station 500 lb. capacity at 6" center of gravity each side Fixed table height of 37" with the table flat Two 24" round work tables Top table assembly has 180 ° pneumatic rotation Servo drive that can be installed on any robotic system with the proper relays Serial # 1906  

RP612017 Preston-Eastin Model RHSDS-5 Dual Sided Robotic Headstock/Tailstock Dual sided for loading/unloading on one side while welding on the other Shot pins for precise positioning 500 lb. balanced load capacity on each side 6’ length capacity 24” diameter capacity Dual Allen-Bradley SLC-150 controls, one for each of the headstock/tailstocks Serial #RHSDS-5-6  

RP9901001A Aronson Ride-5, Double Ended Tilt and Rotate Robotic Indexing Positioner This two-station tilt/rotate positioner has a capacity of 500 lbs. per table at 6" center of gravity Tilt and 3" center of gravity Rotation 180◦ sweep in 7 seconds with .0001 repeatability Two 18" diameter tables with slots 8 non-adjustable index stops for the table rotational axis 4 non-adjust6able index stops for the tilt axis Can be connected to any robot with compatible I/O This is an indexing type system, not servo Serial #N/A  

RP004002 ABB/ESAB Orbit 160B, Robotic Positioner Two station articulating positioner for load & weld station, 353 lbs. each side Table rotation 90° in 2.7 seconds or 360° In 6.8 seconds Tilting arm: turning speed 0 to 11.8 RPM, indexing 90° 2.7 seconds, 360° 7.2 seconds, and station interchange 3.5 seconds This unit was integrated to ABB/ESAB an IRB 6l2 robot. Pos. Serial #414 441 9034, cont. 443 440 9005

RP307001 Aronson Ride-5, Double Ended Tilt and Rotate Robotic Indexing Positioner This two-station tilt/rotate positioner has a capacity of 500 lbs. per table at 6" center of gravity tilt and 3" center of gravity rotation 180 ° sweep in 7 seconds with .0001 repeatability Two 18" diameter tables with slots 8 non-adjustable index stops for the table rotational axis 4 non-adjust6able index stops for the tilt axis Can be connected to any robot with compatible I/O This is an indexing type system, not servo Serial #843

RP210003P Koike-Aronson RHS10/T2.5-30SD Robotic "Skyhook" Positioner 2500 lb. Load capacity Center of gravity 28" Overhang 3" Off-center 38" table Backlash control and "zero" indicator on control "Skyhook" positioners provide part rotation in two 360° axis which result in partial or full inverting of the work piece Serial #869

RP809023 Aronson RDE-RHS10/T3-42SD Double Ended Robotic Skyhook Positioner A two station articulating positioned for loading and weld station Each side has a capacity of 3,000 lb. at 18” center of gravity 12” offset tables from the center of the horizontal rotational axis. 36” diameter round tables with 8.25” thru holes Serial #882

RP809024 Aronson RDE-RHS10/T3-42SD Double Ended Robotic Skyhook Positioner A two station articulating positioned for loading and weld station Each side has a capacity of 3,000 lb. at 18” center of gravity 12” offset tables from the center of the horizontal rotational axis 36” diameter round tables with 8.25” thru holes Serial #881

M404001 Precision 9’ x 9’ x 27-1/2’ Heavy Duty Manipulator/Travel Car System This system was manufactured for the robotics industry for precision welding on military vehicles Heavy duty mast has 9 ft. of constant speed of precision screw driven lift starting at approx. 36” from the floor to 144” high under the boom The mast has manual rotation with lock Boom has 9 ft. of “Dual Pinion” variable speed gear drive and rolls on Thompson Roundway roller system Weight capacity approx. 750 lb. Travel car is 5’ x 5’ x 19” high and variable speed rack & pinion drive on 33 ft. of Thompson Roundway precision track. All three axis paths are accordion booted This system is now Servo driven We will change to Pendant AC-Inverter or D.C. Drives


USED RESISTANCE WELDERS

SP140932P Taylor-Winfield 70 KVA Spot Welder 12" throat depth 16" to 40" diameter capacity Entron Type EN1001/S6.1200E programmable control Water cooled tongs Foot pedal control Control Serial #25276-1 230 volt, single phase Shipping Dimensions: 4'L x 3'W x 5'H Shipping weight: 450 lbs.  

SP306005C KSM/Powerbond 3 KVA 3-Phase Resistance Welder 3 KVA output at 50% duty cycle 460 volt 3-phase input 17” gap x 40” x 5/8” table dimension Mechanical controls for all functions Serial # 2352  

SP510017A Miller 10 KVA 1-Phase Spot Welder Model # mps-10 AFT 10 KVA output at 50% duty cycle 460 volt 1-phase input 2” gap x 18” tong dimension Water cooled Mechanical controls for all functions Serial # JA454057

SP510018A Miller 10 KVA 1-Phase Spot Welder Model # mps-10 AFT 10 KVA output at 50% duty cycle 460 volt 1-phase input 3” gap x 12” tong dimension Water cooled Mechanical controls for all functions Serial # HK253329

SP510019A Airco 10 KVA 1-Phase Spot Welder  Model # mps-10 AFT 10 KVA output at 50% duty cycle 460 volt 1-phase input 1 1/2” gap x 20” tong dimension Water cooled Mechanical controls for all functions Serial # RP20D

SP120903A Taylor-Winfield 10 KVA Spot Welder Model # EB2-8-10 Air 10 KVA output 220 volt 1-phase input 3” gap 8” throat dimension Water cooled Pneumatic clamping Entron control for all functions including single or repeat and weld count Serial # 661163

SP503002 Sciaky 50 KVA Three Phase Press Type Spot Welder  Type PMC02ST Machine # 4540 throat 10” x 36” with 8” extensions for a maximum of 44” This machine has a Medar Three Phase Control Model Legend F.W.F.C. Serial # 100-552 Dwg. ES-83069

SP103523 Taylor Winfield 70 KVA, Equalizing Rocker Arm Welder “1996” very little use Mach. #960180 70 KVA 460 Volt 20”depth Water cooled Self-equalizing arms High production system with quick manual part indexing for rotation and forward- back feed These machines (we have 3) were designed for production welding of washer/dryer tubs “1996”

SP110401 Sciaky 75 KVA 3-Phase Spot Welder Model # PMCO/STIC-75-36 75 KVA output 460 volt 3-phase input 10” x 36” throat dimension Water cooled Dual 2” x 5” air cylinders Mechanical controls for all functions Serial # 10839

SP120709P Taylor Winfield 75 KVA Resistance Seam Welder Model # LSC-30-UGD 75 KVA output 26” throat dimension 10” x 50” Diameter 7” Seam wheel 28-130 in/minimum, depending on wheel size Water cooled Single air cylinder Interlock Industries Model 105 control for all functions 460 volt, 3-phase input. Serial # 42949A  

SP103524 Taylor Winfield 85 KVA, Equalizing Rocker Arm Welder“1996” very little use Mach. #960177 85 KVA 460 volt 20”depth Water cooled, self-equalizing arms High production system with quick manual part indexing for rotation and forward- back feed These machines (we have 3) were designed for production welding of washer/dryer tubs

SP103525 Taylor Winfield 85 KVA, Equalizing Rocker Arm Welder  “1996” very little use Mach. #960179 85 KVA 460 volt 20”depth Water cooled self-equalizing arms High production system with quick manual part indexing for rotation and forward- back feed These machines (we have 3) were designed for production welding of washer/dryer tubs

SP912012 Conrac Model I290G 125 KVA Spot Welder 125 KVA at 5% duty cycle 8” throat depth capacity Serial #L12138

SP131207 Acme 200 KVA Longitudinal Resistance Seam Welder 200 KVA output 28” throat dimension 8” seam wheel Water cooled Single 6” diameter air cylinder 6” stroke Unitrol Model 9180-400 control for all functions 460 volt Pneumatic Serial # N/A Shipping weight 4,200 lbs.  

SP131208 Federal 200 KVA Circumferential Resistance Seam Welder Model # 630517-10 200 KVA output 42” throat dimension 10” x 50” diameter 7” Seam wheel 28-130 in/minimum depending on wheel size Water cooled Single 4” diameter air cylinder 1-1250 psi welding force Unitrol Model 9180-40P control for all functions 460 volt Pneumatic Serial # 630517-10 Shipping weight 4,000 lbs.


USED CUTTING MACHINES

CM140404A BUG-0343 Bug-o DC IV Drive Only As-Is Only Dual speed, 1.5-30 IPM and 8-160 IPM 8' track with 4 dual magnet assemblies Torch holder and rack assembly included Can be used for either cutting or welding applications · Cutting torch NOT included 115 volt Serial #0641095

CM140405A BUG-5100 Cutting System As-Is Only 1.5-30 ipm variable speed range 20' forward and reverse directional pendant control 6' track with 2 each dual magnet assemblies Torch holder and torch rack assembly included · Cutting torch NOT included 115 volt Serial #2685-50-CBG  

CM141201A Koike Model PICLE1-11 Portable Pipe Cutting Machine 4” to 24” diameter capacity with standard chain – Can be increased with the purchase of more new chain Removable chain links for different pipe sizes Manual rotation (no power needed) Set up for acetylene torch Shipping dimensions: 24”Lx16”Wx20”H Shipping weight: 25 lbs.

CM141202A Koike Model PICLE1-11 Portable Pipe Cutting Machine 4” to 24” diameter capacity with standard chain– Can be increased with the purchase of more new chain Removable chain links for different pipe sizes Manual rotation (no power needed) Set up for acetylene torch Serial #510231 Shipping dimensions: 24”Lx16”Wx20”H Shipping weight: 25 lbs.

CM141203A Koike Model PICLE1-11 Portable Pipe Cutting Machine 4” to 24” diameter capacity with standard chain– Can be increased with the purchase of more new chain Removable chain links for different pipe sizes Manual rotation (no power needed) Set up for acetylene torch Serial #106063 Shipping dimensions: 24”Lx16”Wx20”H Shipping weight: 25 lbs.

CM141204A Koike Model PICLE1-11 Portable Pipe Cutting Machine 4” to 24” diameter capacity with standard chain– Can be increased with the purchase of more new chain Removable chain links for different pipe sizes Manual rotation (no power needed) Set up for acetylene torch
Serial #43038
Shipping dimensions: 24”Lx16”Wx20”H Shipping weight: 25 lbs.

CM141205A Koike Model Auto PICLE1-S Remote Control Pipe Cutting Machine 6” to 24” diameter capacity with standard chain– Can be increased with the purchase of more new chain Removable chain links for different pipe sizes Powered rotation at 4-28 IPM Set up for acetylene torch 20’ pendant Serial #807009 Shipping dimensions: 24”Lx16”Wx20”H Shipping weight: 50 lbs. 115 volt AC  

CM141004 Hypertherm Plasma Cutter Model HT4400 High speed system 1/8- 1-1/4” thickness capacity at 30-160 IPM 400 AMPS 100% duty cycle 460 input power 3-phase Power supply Gas mixer Cooler Counter Manual Serial #4400-000187

CM141005 Hypertherm Plasma Cutter Model HT4400 High speed system 1/8- 1-1/4” thickness capacity at 30-160 IPM 400 AMPS 100% duty cycle 460 input power 3-phase Power supply Cooler Counter Manual Serial #4400-000188 

CM131101 CWI Model RB-3550 Oxy-Fuel Circle Burner 1.5” to 42” diameter capacity 4” to 42” square cut holes Rise & fall range from 0 to 7” Control cable, torch adjustment racking and torch mount are new 120 volt Serial # D-091453

CM131019 Bug-O Model Mark 3 Bug-O cutting carriage 8’ section of track Uses standard 8' sections of track Magnetic track mounts Carriage options include: Idler carriage, rack arm, rack box, forward & reverse limit switches and gun/torch holder 2-80 IPM speed range 12” of reach from center of carriage 115 volt

CM110422P Cypress CB-1P Circular Plasma Burner 1” to 12” diameter capacity Rise & fall range from 0 to 5” Vertical & horizontal torch adjusters Includes CWO 4540 carriage with lifting winch Includes Thermal Arc Pak 5XR power supply and plasma torch 120 volt Serial # 041202

CM904011 Linde Model CM-45 Track Cutting Machine Variable speed friction driven carriage 4.25” to 20.5” adjustable reach · Cutting torch NOT included 120 volt Serial #2X2 New track available at additional cost

CM100612 Linde Model CM-79 Cutting Machine with 2 six foot pieces of track 250 lb. capacity Variable speed 60 IPM 0-4” thickness capacity 2-54” circle cutting range 115 volt Serial #75A-01195 Cutting torch available for additional cost Included 2 new 6’ pieces of track 6’, 7 ½’ and 9’ track sections available for additional cost Shipping dimensions: 72”Lx7 Ό”Wx7”H (with track) Shipping weight: 60 lbs. (with track)  

CM120805 Gullco Kat Model GK-191 Gullco Rigid “KAT” welding/cutting carriage Uses standard or deep section track 60” sections of track 15’ of track included Carriage options include: Idler carriage, rack arm, rack box, forward & reverse limit switches and gun/torch holder 1.5-51.5 IPM speed range 12” of reach from center of carriage 115 volt Serial # 4251

CM901026 Bug-O DC Speed Weaving Welding Kit Kit Includes 1 each of the following: DC-IV variable speed carriage Speed Weaver II Weaver swivel mount Cable mounting assembly 93.5” rigid rail w/ magnet assemblies and 46.5” rigid rail w/ magnet assemblies 120 volt Serial #3737-50/3734-50

CM303001 Linde Shapemaker 48" Template Cutting Machine Magnetic template tracing contour cutter Size capacity is any shape that will fit in a 48" circle Push button RC control Floor model on "H" base · No torch or cutting equipment included Serial #0351-18

CM303017A Heath Shapemaker 48" Template Cutting Machine Magnetic template tracing contour cutter Size capacity - any shape that will fit in a 48" circle Push button RC control Floor model on "H" base No torch or cutting equipment included Serial #0351-18 Good Condition  

CM608014P Heath Ultra-matic Model 500-24 Pipe Cutter 5” to 24” diameter capacity Dual clamping Straight or profile cuts Variable speed Forward/Reverse 9” Fine adjustment and 24” coarse adjustment cutting torch slides 460 volt 3 phase Serial # 22265

CM120408C Koike Auto-Picle-S Portable Pipe Cutting Machine Remote pendant with 15 ft. cable Variable speed chain/friction driven carriage 6” to 24” diameter capacity 25” to 60” with additional guide rail Pipe cutting thickness from 3/16” to 2” · Cutting torch and chain NOT included 120 volt Shipping weight 33 lbs. Serial #13031

CM120409C Koike Auto-Picle Portable Pipe Cutting Machine Remote pendant with 15 ft. cable Variable speed chain/friction driven carriage 6” to 24” diameter capacity 25” to 60” with additional guide rail Pipe cutting thickness from 3/16” to 2” · Cutting torch and chain NOT included 120 volt Shipping weight 33 lbs. Serial #807009 

CM140709A Koike IK-70 Portable Single Purpose Circle Cutter Free standing with counter weight Ό” – 2” plate thickness Cutting diameter: 1 3/16” – 40” 0.04-1.5 RPM torch rotation 0 to 45° cutting angle adjustment Speed control: PWM control 15W DC 20” incremented slide 6” vertical adjustment 20” adjustable reach arm Centering tip Hi-lo positioning 115 volt Serial #83003 Shipping weight 121 lbs.

CM140710A Victor CD-2000 Shape Maker 6” minimum cutting capacity 16” maximum cutting capacity 12” manual vertical adjustment Steel template to guide cutting torch Magnetic base to secure to work piece

CM140711A Custom/Bug-O Model 1240 180° Cutting Machine Bench top model 12” minimum diameter 40” maximum diameter Bug-O Mark 3 rotation control Bug-O 10” powered vertical rack and pinion slide Pendant control 115 volt  


FABRICATION TOOLS AND EQUIPMENT

FAB110107P Hydraulic Head Press  20” diameter capacity 24” to 36” tank length capacity Hydraulic driven press cylinder with pump Overhead boom to assist in loading and un-loading of parts Just Out of Service – Quick Turn Around

FAB701006 Whitney 4” x 4” x 3/16” Hydraulic Angle Iron Shear Shear with hydraulic cylinder mounted in a bench mount frame · Hydraulic pump NOT included Serial # N/A

ME408007 Gullco Plate Beveller Model BCM-12 5/8" capacity Mounted on roller base stand 230/460 volt 3-phase Serial #71382-1  

FAB130706 Webb Model R3R-8010 Plate Bending Roll As Is 24”-84” work diameter 10' length capacity 3/16 material thickness capacity 3 roll, Initial pinch and slip roll setup Hydraulic hold down 230 volt - 3 phase Serial # 6430

FAB140806C Blue Valley Model #4 Flanger 3/8” capacity Complete hydraulic unit Main drive motor Side guide rolls Electrical controls New in 1986 220/440 volt – 3 phase Serial #686 Shipping dimensions approx.: 160”L x 96”W x 80”H Weight: 7,000 lbs.  

FAB130801 Famco Model M 54 Shear 16 gage maximum capacity 54” total cutting blade length 52” cutting capacity with alignment bar Manual foot pedal actuation 230/460 volt 3Phase Serial # S-K64YP82 

FAB110408P DoAll Model 3012-U Vertical Band Saw 24” x 24” table working surface 30” maximum throat capacity 12” maximum vertical adjustment Floor to table 47” Roller cart with brake for easy movement Serial # 147-671006 230 volt 3 phase Shipping weight 1,100 lbs. 

FAB131116P Marvel Model 81A9 Vertical Band Saw Tilt frame 18” x 20” 30” x 27” table working surface 14'6” x 1 1/4” blade Saw comes with conveyor and feed table Floor to table 38” Maximum vise opening 21 1/2” Serial # D-384988-I 460 Volt Shipping weight 6,000 lbs.

 MISCELLANEOUS EQUIPMENT

WPI FRS1 Arc Wand Model 882 Flux Recovery System Heavy duty double tank stationary unit 2 H.P. motor Positive displacement vacuum pump 45 lbs./min. recovery rate Attached 150 lb. hopper capacity Rated for 24/7 continuous operation 230/460 volt 3 phase Serial # 36AF47713. Shipping weight 650 lbs.

ME130125 Clean Air Equipment Smoke Eater Model DFL-12 12 filters 2,712 square inch total filter area 7.5 HP motor 3,500 CFM ABB control Serial #9510-153 Shipping dimensions 7’ x 36” x9 ½’ Shipping weight 1,950 lbs.

ME140311P Weld Engineering Model PS-5000-R Flux Recovery System Semi-Automatic dust collection unit 200 lb. flux hopper/separator and continuous duty vacuum blower motor Mounted on portable running gear 20' of 1 ½“diameter hose with pickup nozzle 230/460 volt 3 phase Serial # 115076W0408 Shipping weight 400 lbs.

ME140402 Heck Industries Turbo-Burr Deburring Tool Hand held deburring tool Can be used on the following: steel, plastics, stainless steel, aluminum and laminates 55,000 RPM rotation speed (no load) 60 to 100 PSI. 5 to 11 CFM. Minimum material thickness .015. 0-.075 bevel depth pneumatic Shipping weight 4 lbs.

ME140403 Weldma Model WM-18 Tungsten Sharpener/Grinder 7,500 RPM 90◦ table swivel Tungsten holder: 1500 RPM, 90◦ swivel in 3◦ increments. 2.5” diameter x 1.25” wide wheel Grinder sits on pedestal base 115 volt Shipping weight 40 lbs.

ME150233P American Manufacturing 2,000 lb. Model M1070 Hydraulic Lift Table 18" x 50" table 2,000 lb. capacity 6" to 42" height Mounted on v-roller wheels that run on inverted angle iron track Serial #39616 Shipping dimensions:88" long x 18" wide x 6" high Shipping weight: 550 lbs.

ME130303 Southworth Model LS 2-36 Lift Table 4’ x 4’ table with turning rolls 2,000 lb. weight capacity 7” to 43” height adjustment Atlas Pipemate 1,000# drive roll and custom idler roll attached to table Foot pedal control 115/230 volt 1 phase Shipping weight 650 lbs.  

ME130511 Pentalift 5,000# Hydraulic Lift Table 39” x 78” table 5,000 lb. weight capacity 21” to 80” height adjustment Foot pedal control 460 volt 3 phase Shipping weight 2,500 lbs. Serial #N/A. 

ME130512 Pentalift 5,000# Hydraulic Lift Table 60” x 74” table 5,000 lb. weight capacity 21” to 80” height adjustment Foot pedal control 460 volt 3 phase Shipping weight 2,500 lbs. Serial #N/A  

ME140919 Welding Wholesale 30” x 60” Weld Platen with stand 8,000 lb. capacity Work surface 32” high from ground 124 - 1 Ύ” x 1 Ύ” square holes 11” high back splash 5/8” angle iron stand Shipping dimensions: 66”L x 36”W x 43”H Shipping weight: 1,700 lbs.

ME140929 Acorn 5’ x 5’ Weld Platen with stand 2” x 2” square holes for fixturing 3/8” angle iron stand with steel tube legs Shipping dimensions: 5’L x 5’W x 30”H

ME130802 South Bend Model 113D Lathe 13” Swing capacity 7’ length capacity 8” 3-jaw chuck 7” manual cross slide for tool adjustment 4 speed 4-224 per inch threading capability Tailstock for boring Tail-end part support Serial # 113D

ME812004 Glegg 2123 Gallon Water Storage Tanks 2123 gallon capacity 5103 Rubber lined Free standing vertical tanks National board N0609 certified MAWP 25 PSIat150 F, MDMT -20 Fat 25 PSI, DSI AS406D

ME000901P Gullco Heavy Duty Mig Welding Carriage Variable speed rack and pinion driven carriage that runs on standard Gullco track Includes a L-Tec model EH-10A 4-roll feed head and a Gullco WS-110 Super Glide seam tracker with 8” vertical and 8” horizontal slides · Probe for seam tracker NOT included Serial #N/A

ME908001 TR-33 Mohawk Four Post Above Ground Vehicle Lift 33,000 lb. capacity 30 ft. wheelbase max. Over 6 ft. lifting height of rails 4 post design allows for more under vehicle access Fast lifting speeds (120 seconds) Synchronized hydraulic direct drive cylinders lift on all four posts with redundant safety systems Serial #98H245

ME908002 FL-25 Mohawk Four Post Fork Truck Lift 25,000 lb. capacity 13 ft. wheelbase max. Over 6 ft. lifting height of rails 4 post design allows for more under vehicle access Fast lifting speeds (120 seconds) Synchronized hydraulic direct drive cylinders lift on all four posts with redundant safety systems Serial #A1F191

VC802003P Airline Model VC-48 Vacuum Chamber 48” diameter x 24” high welding chamber 38” high work table 2 sets of vacuum glove ports Includes a vacuum pump Vacuum gauge and inert gas flow-meter with pressure regulator Serial #193

VC701002 Vacuum Atmospheres Corporation Model HE-233-62 Vacuum Chamber 96” long x 42” wide x 32” high vacuum/welding chamber 39” high work table 5 glove ports on both sides of the 8’ length Includes a Vacuum Atmospheres Corp Model HE-373-BIN (Serial #50517-464) 300◦ 800 watt drying furnace Serial #20922-1

ME704010 Arc-Air Model N-6000 Automatic Gouging System 1600 amp capacity Accepts gouging electrodes from 5/16” to Ύ” diameter System includes torch head Automatic controller 1600 amp contactor Power cable assembly Interconnecting cable assembly Requires 60 to 100 psi compressed air (45 to 80 cfm) 120 volt Serial #1237

ME110703A G&P Model 36” Belt Grinder/Sander Manipulator mounted grinder/sander 36” x 4” grinding surface Uses 4” x 90” belts 3500 RPM Pneumatic belt and head adjustment Manual tilt adjustment Manual push cart included to transport grinding unit 230 or 460 volt 3 phase Serial # G8998 Shipping weight

ME812001 Marindus Model RT-200 De-scaler 8” descaling/scarifing head Unit has interchangeable heads for different operations Manual handle adjustment Vacuum attachment 230/460 volt 3 phase. Shipping weight 175 lbs. Serial # 9202-1301

ME110707A Cullen-Freistedt 20,000# Coil Hook  20,000 lb. capacity steel coil hook 32” x 3” curved lifting face 62”L x 25”W x 72”D Serial # 6623

ME110708A Letellier 30,000# Coil Hook  30,000 lb. capacity steel coil hook 43” x 4” curved lifting face 72”L x 21 1/2”W x 66”D Serial # 33636 Shipping weight 1755#  

ME110210P Walker-Bux BM-110 Lifting Magnets 11,000 lb. maximum capacity Powered by rechargeable battery

ME130509P Walker-Bux BM-110 Lifting Magnet 11,000 lb. maximum capacity Powered by rechargeable battery

ME110214P Walker-Bux BM-55 Lifting Magnets 5,500 lb. maximum capacity Powered by rechargeable battery

ME130508P Walker-Bux BM-55 Lifting Magnet 5,500 lb. maximum capacity Powered by rechargeable battery

ME120750P Reelcraft/MC Doughton Model 7850 Fluid Hose Reels Air Water or oil Spring retractable Bolt down base 1/2” I.D. hose capable Adjustable guide arm Hose included Reconditioned and Ready for Service

ME120777P Ingersoll-Rand Model HL3000K 3.3 Ton Pneumatic hoist 6,600 lb. capacity Air powered (90 PSI) Trolley attachment Trolley beam not included Pendant control Chain with hook 20’ of lift  

ME120779P Ingersoll-Rand Model HLA60A 3 Ton Pneumatic hoist 6,600 lb. capacity Air powered (90 PSI) Trolley attachment Trolley beam not included Pendant control Chain with hook. 20’ of lift Serial # RBG71725  

ME130614 Carolina Tool Model CH-100 Engine Hoist 4,000 lb. capacity fully closed 2,000 lb. fully extended 36” to 11’ lift height Hydraulic Serial # 1095

ME121015 Rol-Lift Model T29 Tire Jack 5,500 lb. capacity Hydraulic 3 ½“diameter x 18” rolls Rolls are 44 ½ center to center 4 ½” stroke 6 ½”-11” to the top of the rollers Serial # T29-17502

ME120707 Sterling Drill Bit Sharpener 1/8” to 2 1/2” capacity Sharpens 2, 3 and 4 flute drills with 90 to 140◦ included angles 480 volt 3phase

ME140804A Weldmatic WD10 wooden Reel Wire Dispenser Dispenses up to 3/32” diameter wire Accommodates up to a 30” diameter reel of wire Spring loaded brake arm keeps wire taut on reel to prevent tangling Requires approximately 5 lbs. of pull to activate a 1000 lb. real of wire at 700 IPM feed rate when properly installed No wire flip Ideal for manual, automatic, semi-automatic and robotic welding Can be used with steel, aluminum, flux-core, and stainless steel wire  

WP141101 Contour Arc/Jetline SWC-5 Flatway Style Sidebeam Carriage Jetline SWC-5 variable speed carriage, 3-135 ipm, 300 lb. capacity @ 12" center of gravity Contour Arc digital carriage/system control Jetline ALC-401-6 arc length control an 6" slide Jetline 2-roll cold wire feeder with controls in the carriage control 6" pneumatic torch lifter 6" manual vertical slide, 2" manual horizontal slide and 2" manual z axis slide Serial #010749 Shipping dimensions: 5'Lx4'Wx3'H Shipping weight: 250 lbs.

WP141102 Contour Arc/Jetline SWCA Roundway Style Sidebeam Carriage Jetline SWCA variable speed carriage, 3-135 IPM, 300 lb. capacity AT 12" center of gravity Contour Arc digital carriage/system control Jetline ALC-401-6 arc length control an 6" slide Jetline 2-roll cold wire feeder with controls in the carriage control 6" pneumatic torch lifter 6" manual vertical slide, 2" manual horizontal slide and 2" manual z axis slide Matheson Tri-Gas Nanochem Inert gas purifier Serial #010750 Shipping dimensions: 5'Lx4'Wx3'H Shipping weight: 250 lbs.

WP141103 Contour Arc/Jetline SWCA Roundway Style Sidebeam Carriage Jetline SWCA variable speed carriage, 3-135 IPM, 300 lb. capacity at 12" center of gravity Contour Arc digital carriage/system control Jetline ALC-401-6 arc length control an 6" slide Jetline 2-roll cold wire feeder with controls in the carriage control 6" pneumatic torch lifter 6" manual vertical slide, 2" manual horizontal slide and 2" manual z axis slide Serial #010751 Shipping dimensions: 5'Lx4'Wx3'H Shipping weight: 250 lbs.

WS100546P Pandjiris 4 Head Gantry Welding System Heavy duty gantry mounted on twin powered travel cars that runs on twin 60 lb. track with 59” between rails 166” side beam with 60” powered vertical lift (currently configured for 36”) Two powered travel carriages, each with 2 Lincoln NA-5 heads and 2 Cyclomatic mechanical seam trackers 4 Lincoln DC-1000 power supplies Invincible flux recovery system



Weld Plus Inc Ad Banner

Welding Rotators, Manipulators, Weld Positioner, Used Turning Rolls,
Longitudinal Seam Welders, Turntables, Headstock and Tailstocks,
Lathes and Circumferential Welders.

steel wheel turning rolls


We are a complete service sales rental parts used weld equipment and repair company. Weld Plus Inc.
can fill all your used welding machinery requirements. Pipe fabrication welding positioner, columns booms
manipulator, tank turning rolls, indexing turntables, welding lathes, seamers and vessel rotators from
manufacturers such as Aronson, Ransome, Pandjiris, Koike, Gullco, Bancroft, Bug-O, Preston - Eastin,
Worthington and Jetline. We buy, sell and rent new and reconditioned used equipment and machines.

513.941.4411 - 1.800.288.9414 - Fax 1.513.467.3585
sales@usedweldingmachinery.com
Send mail to webmaster@usedweldingmachinery.com 
with questions or comments about this web site.
Site Map
Copyright © 1996-2015
Last modified:
December 17, 2015