Used  Welding Machinery Monthly Sales Products Special Sales Contact Us Site Map



6 ft. X 10 ft. Travel Car Pandjiris Manipulator System. This Sub Arc Manipulator has
a  Seamed Tracking System  mounted on a Variable Speed Travel Car The Manipulator has
6’ of vertical. lift with bottom of the boom from 3 ft to 9 ft. from floor. 10 ft. of Var. Speed Reach. Manual Mast Rotation, 60" X 44" welder platform on mast. 400 lb load capacity each
end of boom. 13 ft. of Horizontal. Boom. 15ft. 3". Single Pendant Joy Stick control of
Manipulator - Travel Car. Weld package includes: Miller SubArc Manipulator System 9
Control, Cyclomatic Seam Tracker with weld enable-overlap-retract option, 180 to 90
Degree Head Bracket, Air Flux Recovery Sys., 650 amp CV Power Supply.

Web Site Weld Manipulator Listings

Pipe Positioners

Positioners for Pipe Welding Fabrication

1 ea P805013 Ransome Model 30P 3,000 lb Positioner. 3,000 lb capacity @ 6" c.g., Power tilt. Variable speed rotation from .03 to 1.2 RPM. Fixed table height of 38-3/4" to the center of the rotational axis. 40" square table with slots. Pendant control. 230 or 460 volt. Serial #4840 Good Condition

1 ea P611020 Aronson Model HS30GE/T4-62 Sky Hook Positioner. 4,000 lb Capacity @ 36" C.G. Off of the Turntable Face. 62" Clearance from Center of Turntable. "Skyhook" Positioners Provide Part Rotation in Two 360 Degree Axis which Result in Partial or Full Inverting of the Workpiece. Pendant Control. Serial #7914 Good Condition

P810026 Aronson GE-45 Geared Elevation Positioner. 4,500 lb capacity @ 12” c.g.. 135 degree power tilt. .01 to 1.2 variable speed rotation. Powered elevation from 53” to 86”. 42” square table with slots. Pendant control. Serial # n/a Good Condition

P810018 Aronson X21E Geared Elevation Positioner. 5,000 lb capacity @ 6” c.g.. 135 degree power tilt. Variable speed power rotation. Powered elevation from 53” to 77”. 48” diameter round table with slots. Pendant control. Serial #665 Good Condition

1 ea P806004 Cullen-Friedstat Model 60 6,000 lb Positioner. 6,000 lb capacity @ 12" c.g.. Power tilt. Variable speed rotation. Manual adjustable height from 34.75" to 56.75" in 5.5" increments. 36" diameter table with slots. Pendant control for all functions. 230/460 volt. Serial #204 Good Condition

1 ea RP309001P Koike-Aronson "1994" Model #RDCG/T6-100/26SD "Drop-Center" Positioner. Tilt Capacity of 6600 lbs @ 24" from the table, or 4000 lbs @ 57", or 2000 lbs @ 90"!!. Rotation Capacity of 6600 lbs @ 20" Center of Gravity off of the centerline of rotation. Both Tilt and Rotation Axis have Adjustable Anti-Backlash Dual Pinions on Bull Gears! Both Axis are Servo Drive Variable Speed with Encoders and Resolvers. 360 deg. Rotation @ 0.0-2.0 RPM, 200 deg. Tilt @ 0.0-1.75 RPM. (This Servo Drive Positioner can be converted to a Manual Pendant Operated Machine). Table is 48" x 48" with Hydraulic Master Clamping System for Slave Pallet Mounted Tooling 1 ea slave included. Note; "Drop Center Positioners" are typically used for work pieces with longer Center of Gravity distances from the table, resulting in lower working or welding heights than using higher capacity positioners. This 1994 Machine has NEVER BEEN USED! Brand New Condition!

P810001 Aronson 180T120/CC 180 Degree Tilter. 7,000 lb weight capacity @ 12” c.g. from table. Table tilts 180 degrees from vertical to vertical. For positioning long work pieces such as long truck  frames for down hand welding. Table does NOT rotate. Table is a dual screw clamping table with an internal capacity of 40” wide x 27.5” high Very Good Condition

1 ea P805005 Teledyne-Readco Model UHSE-400 7,500 lb Side Arm Positioner. Side arm positioners are also known as Skyhook positioners. 7,500 lb capacity @ 6" c.g.. Dual screw driven powered elevation from 31.5" to 77.5" with the side arm table flat and parallel to the floor. 51" to the center of the rotational axis with the side arm at 90 degrees to the floor. Side arm table is 3.5" off set to the center of the rotational axis on the headstock. Variable speed rotation of the side arm table. 88" maximum part diameter capacity. Pendant control for all functions. 460 volt. Serial #106130 Good Condition

1 ea P805006 Teledyne-Readco Model UHSE-400 7,500 lb Side Arm Positioner. Side arm positioners are also known as Skyhook positioners. 7,500 lb capacity @ 6" c.g.. Dual screw driven powered elevation from 31.5" to 77.5" with the side arm table flat and parallel to the floor. 51" to the center of the rotational axis with the side arm at 90 degrees to the floor. Side arm table is 3.5" off set to the center of the rotational axis on the headstock. Variable speed rotation of the side arm table. 88" maximum part diameter capacity. Pendant control for all functions. 460 volt. Serial #106133 Good Condition

P808011 Aronson GE-90A 9,000 lb Geared Elevation Positioner. 9,000 lb capacity @12” c.g.., 135 degree power tilt. Variable speed rotation from .04 to 1.0 rpm. 33” powered geared elevation from 54.5” to 87.5”with the table flat. 42” diameter round table with a 9” diameter thru hole. Pendant control for all functions. Serial #7019. Good Condition.

Web Site Weld Positioners Listings


Powered Turning Rolls

 

IRC 15 5D/5I "NEW" Irco Automation 20,000 lb. Turning Rolls. Set Includes 1 15-5 Driver and 1 15-5 Idler (add extra Idler for 30,000 lb Capacity). 12” Diameter x 3" Wide Rubber Wheels, 2 Wheels per Axle for a 6” Total Wheel Face. For Diameters from 12” to 12’. Variable Speed from 2 to 55 IPM. With Remote Pendant Control. 460 Volt. Shipping Weight 1,550 lbs./set. Ready to Ship! New

IRC 30 10D/10I "NEW" Irco Automation 40,000 lb. Turning Rolls. Set Includes 1 30-10 Driver and 1 30-10 Idler (add extra Idler for 60,000 lb Capacity). 12” Diameter x 4" Wide Rubber Wheels, 2 Wheels per Axle for a 8” Total Wheel Face. For Diameters from 12” to 12’. Variable Speed from 2 to 55 IPM. With Remote Pendant Control. 460 Volt. Shipping Weight 1,850 lbs./set. Ready to Ship! New

PAN MM30/15 "NEW" Pandjiris Missouri Mule 30/15 Turning Rolls. Drive and Idler. 60,000 lb Weight Capacity. 12" to 16’ Diameter Capacity. Variable Speed from 5.3 to 53 IPM. 20" Diameter x 10" Wide Rubber Wheels. Pendant Control. 460 Volt "NEW"Additional Idlers Available

IRC 45 15D/15I "NEW" Irco Automation 60,000 lb. Turning Rolls. Set Includes 1 45-15 Driver and 1 45-15 Idler (add extra Idler for 90,000 lb Capacity). 20” Diameter x 4.5" Wide Rubber Wheels. For Diameters from 12” to 20’. Variable Speed from 1.5 to 45 IPM. With Remote Pendant Control. 460 Volt. Shipping Weight 3,550 lbs./set. Ready to Ship! - New

ARO CPRR / CIRR “NEW” Ransome 60 Ton “C” Series Turning Roll Set. Set includes 1 each CPRR drive unit and 1 each CIRR idler unit for a capacity of 60,000 lb (add an additional idler for a total capacity of 90 ton.). Variable Speed drive from 1.45 to 58 ipm. 20.5” diameter x 14” wide rubber wheels. For diameters from 7” minimum to 20’ maximum. 20’ Pendant control for all functions. 460 volt. Shipping weight 5,600 lbs/set. NEW – Ready to Ship

1 set PRE Preston-Eastin "NEW" TDRA/TIRA-120-22D, 240,000 lbs, 120 Ton, Turning Rolls. Set includes 1 ea TDRA-120, 120,000 lb Driver, and 1 ea TIRA 120,000 lb Idler. for a Total Capacity of 240,000 lbs or 120 tons. This set will Turn and Support 360,000 lbs or 180 tons by adding optional extra TIRA-120 Idler. Three (3) Tires 20" dia. x 8" wide and Four (4) Overload Disc per Axle. For work rotating diameters from 8" to 22 ft., Variable Speed Rotation by Inverter Drive with 20 ft Remote Pendant Control. 460 volt input. "New" in our Stock!

Web Site Power Turning Rolls Listings


January | February | March | April | May | June | July
August
| September | October | November | December


513.941.4411 - 1.800.288.9414 - Fax 1.513.467.3585
sales@usedweldingmachinery.com
Send mail to webmaster@usedweldingmachinery.com 
with questions or comments about this web site.
Site Map
Copyright © 1996-2009 Weld Plus Inc.
Last modified: January 11, 2009